• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Palit RTX 5090 GameRock 32GB Water Block with Backplate – Bykski N-PT5090GK-SR-V2

stars, based on ( 0 ) review
$217.33 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-PT5090GK-SR-V2

Full-cover water block for Palit RTX 5090 GameRock

The Bykski N-PT5090GK-SR-V2 is a full-cover GPU water block for the Palit GeForce RTX 5090 GameRock 32GB PCB shown below. It replaces the stock cooler and transfers heat from the GPU core, memory, and voltage regulators to the coolant in a custom loop. A separate aluminum backplate mounts behind the board.

Fits
Palit RTX 5090 GameRock 32GB
Cold plate
Nickel-plated T2 copper
Ports
G1/4 female thread
Backplate
Passive aluminum

Compatibility

Bykski lists this graphics card for the SR-V2.

  • ✓Palit GeForce RTX 5090 GameRock 32GB

Before ordering, match your card's PCB to the photo, including the mounting holes, component positions, and power connector.

Bykski N-PT5090GK-SR-V2 compatibility photo of the bare Palit GeForce RTX 5090 GameRock PCB with the GPU, memory, and mounting holes visible

Bare Palit GameRock PCB shown in Bykski's compatibility guide.

Design Highlights

Bykski N-PT5090GK-SR-V2 rendered at an angle with the dark panel, exposed fasteners, and short-edge terminal visible

Stainless steel panel with short-edge ports

The 304 stainless steel panel covers the front of the block. Both G1/4 connections sit at the short end, where the tubing and fittings need clearance.

Bykski N-PT5090GK-SR-V2 underside rendering showing the machined cold plate contact surfaces and mounting posts

Copper cold plate for the GPU, memory, and VRM

The nickel-plated cold plate has machined contact areas for the GPU die, memory, and designated voltage regulator components. Inside the block, coolant flows through 0.3 mm jet microchannels.

Key Specifications

Model (SKU)N-PT5090GK-SR-V2
Cold plateNickel-plated T2 copper
Front panel304 stainless steel
Block finishTitanium gray
BackplateBlack aluminum, passive
Water block (L × W × T)233.66 × 136.25 × 17.00 mm
Backplate (L × W × T)209.97 × 136.25 × 3.96 mm
Port threadG1/4 female
Microchannels0.3 mm, jet flow
Seal materialEPDM
Net weight1.68 kg
Maximum working pressure2 bar
Block temperature range−20 to 60 °C
Bykski N-PT5090GK-SR-V2 drawing with face and edge views of the water block and backplate, dimensioned in millimeters

Bykski's dimension drawing. Water block above, backplate below. Dimensions in millimeters.

Which Version Do I Need?

Choose the panel and port layout that suit your build. Check the PCB guide on the listing for the version you choose.

Bykski N-PT5090GK-SR-V2THIS PAGE
Choose this version for a stainless steel front panel with the ports at the short end.
Choose this version for a clear coolant window, short-edge ports, and 5V 3-pin ARGB.
Choose this version for a clear top and a port terminal centered on the long edge.

What's in the Box

1 × full-cover GPU water block1 × passive aluminum backplateThermal pad setMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski N-PT5090GK-SR-V2 straight-on rendering of the separate dark backplate and its mounting holes

Included passive aluminum backplate.

Installation & Use

1
Shut down and disconnect the PC. Remove the graphics card and take off its stock cooler and backplate.
2
Clean away the old thermal paste and pad residue. Check the fit and make sure the mounting holes line up.
3
Cut the included thermal pads to fit the memory and voltage regulator components marked in the diagram. Peel the protective film from both sides of each pad and apply your own thermal paste to the GPU die.
4
Align the water block and backplate with the PCB. Start the screws by hand and tighten them evenly in stages.
5
Use G1/4 fittings to connect the inlet and outlet to your loop. Run only the pump while you check the filled loop for leaks. Power the graphics card after the loop passes the test.

You also need a pump, radiator, G1/4 fittings, tubing, and coolant.

Bykski N-PT5090GK-SR-V2 installation drawing with gray pad locations around the center GPU die and along both sides of the PCB

Bykski pad map. The light gray areas show pad locations on memory and power components. Apply thermal paste to the central GPU die.

FAQ

Will this water block fit my RTX 5090?

Bykski lists the Palit GeForce RTX 5090 GameRock 32GB for this SKU. Compare your card's PCB to the photo before ordering.

What fittings should I use?

Use G1/4 fittings sized for your tubing.

Where do the thermal pads go?

Place the pads on the memory and voltage regulator components highlighted in gray in the installation diagram.

Where does the backplate sit?

The included passive aluminum backplate mounts behind the graphics card PCB, outside the coolant loop.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • The product does NOT come with English instructions.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.

FormulaMod Official Store

Recent Reviews
+