• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Barrow

Lian Li O11 Dynamic XL Waterway Plate | Barrow LLO11-SDB XL

stars, based on ( 0 ) review
€130.86 piece
items available
Contact Us
FormulaMod Official Store
Barrow · LLO11-SDB XL

Single-GPU waterway plate for the Lian Li O11 Dynamic XL

The Barrow LLO11-SDB XL is a frosted acrylic waterway plate for the original Lian Li O11 Dynamic XL. It brings the tubing connections for a single-GPU custom loop together on one plate beside the motherboard. Barrow uses G1/4 fittings for the loop and recommends a separate SPB17-T PLUS pump.

Fits
Lian Li O11 Dynamic XL
Fittings
G1/4
Lighting
5V 3-pin ARGB
Pump
Sold separately

Compatibility

  • ✓Lian Li O11 Dynamic XL (O11DXL-X, O11DXL-W, O11DXL-A)

Not compatible:

  • ✗Lian Li O11 Dynamic EVO XL
  • ✗Lian Li O11 Dynamic (non-XL)

Use the exact case model and check the port positions on your CPU and GPU blocks before ordering.

Barrow LLO11-SDB XL installed vertically beside the motherboard in a Lian Li O11 Dynamic XL with red tubing and one graphics card

Single-GPU build shown with separately purchased loop components.

Design Highlights

Barrow LLO11-SDB XL distro plate with red, purple, blue, and green lighting along the edge

Replaceable 5V ARGB strip

The included strip runs along the edge of the acrylic plate. Use a Barrow LRC 2.0 lighting controller or a conversion cable for a compatible 5V ARGB motherboard header.

Barrow LLO11-SDB XL unlit frosted acrylic plate showing the channels and threaded openings

Coolant channels in the plate

The channels give the CPU block, GPU block, and radiators a shared place to connect their tubing. Plan the tube runs around the inlet and outlet on each block.

Key Specifications

ModelBarrow LLO11-SDB XL
Plate materialFrosted acrylic
Fitting threadG1/4
Lighting systemBarrow LRC 2.0, 5V 3-pin ARGB
Recommended pumpBarrow SPB17-T PLUS, 17W PWM, sold separately
Radiator layout shown by BarrowTwo 360 mm radiators, top and bottom
Motherboards listed by Barrow
View listed models

ASUS ROG Strix: Z390-E Gaming, Z390-H Gaming, Z370-E Gaming, Z370-F Gaming, Z370-H Gaming, B360-F Gaming, Z270E Gaming, Z270F Gaming, Z270H Gaming.

ASUS ROG Maximus: XI Extreme, XI Gene, XI Hero, XI Hero Black Ops 4 Edition, X Hero, X Hero (Wi-Fi AC), IX Hero, VIII Extreme/Assembly, VIII Hero, VIII Ranger.

Other ASUS models: Prime Z370-A, Prime Z390-A, Prime Z390-P, TUF Z370-Pro Gaming, TUF Z390-Pro Gaming, Z170 Pro Gaming, Z170-AR.

CPU blocks shown by BarrowLTYK3-04 V2, LTYKB-04N-V2, LTYKB-ARK, LTFHB-04N V2, FBLTFHI-04N V2.
Barrow LLO11-SDB XL close-up of several threaded openings at one end of the plate and the channels leading to them

Which Version Do I Need?

Match the plate to your case model and preferred mounting position.

Barrow LLO11-SDB XLTHIS PAGE
Choose this plate for the original O11 Dynamic XL.
Choose the side-mounted plate for the original non-XL O11 Dynamic.
Choose the front-mounted plate for the original non-XL O11 Dynamic.

What's in the Box

1 × distro plate1 × 5V ARGB strip1 set of mounting screws

The With Manual Controller option adds a manual lighting controller. The No Controller option includes the same plate, strip, and mounting screws.

Installation & Use

1
Position the plate beside the motherboard and start the mounting screws loosely.
2
Position the pump and radiators, then plan the tubing to match the inlet and outlet positions on your CPU and GPU blocks.
3
Finish routing the tubing before tightening the plate’s mounting screws.
4
Leak-test the completed loop and make sure the hardware is dry before powering the PC.

For the loop, you also need a pump, CPU and GPU water blocks, radiators, G1/4 fittings, tubing, and coolant.

Barrow LLO11-SDB XL close-up of the threaded pump opening and nearby channels

Pump connection on the plate before the pump is installed.

FAQ

Does this waterway plate fit the O11 Dynamic EVO XL?

It fits the original Lian Li O11 Dynamic XL. The O11 Dynamic EVO XL is a different case and is outside the stated fit.

Does the distro plate come with a pump?

Both options require a separate pump. Barrow recommends the SPB17-T PLUS through-hole PWM pump.

What fittings do I need?

Use G1/4 fittings and choose fittings that match your tubing.

How do I connect the lighting with the No Controller option?

Use a compatible Barrow LRC 2.0 controller or a conversion cable to a compatible 5V ARGB motherboard header. Keep the 5V strip off 12V 4-pin RGB headers.

Notes
  • All pumps, radiators, reservoirs, cases, fittings, and other products in details photos are for reference only.
  • The pipe of GPU water block layout are for reference only Actual operation is based on the direction of the water block outlet and inlet
  • As Barrow upgrades or adjusts the contents of the kit from time to time, such as product updates version, model or appearance, adjustments to the layout, etc., If not notified in time, the Barrow's latest real object shall prevail

FormulaMod Official Store

Recent Reviews
+