• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

DDC Pump with PWM and G1/4 Ports, Clear Acrylic Top | Bykski B-PMD3-X

stars, based on ( 0 ) review
$48.46 piece
items available
Contact Us
FormulaMod Official Store
Bykski · B-PMD3-X

DDC pump with PWM control and a clear acrylic top

The Bykski B-PMD3-X is a DDC pump that circulates coolant through a custom PC water cooling loop. Its preinstalled clear acrylic top has G1/4 inlet and outlet ports for connecting the pump to your plumbing. A 12 V Molex connection powers the pump, and a separate PWM lead lets you adjust its speed.

Fits
G1/4 fittings
Power
12 V DC
Speed control
4-pin PWM
Max head
6 m

Use With

Match your fittings, reservoir, and power connections before ordering.

  • ✓G1/4 fittings for the pump inlet and outlet
  • ✓Bykski B-CT50-MBK 50 mm reservoir for direct mounting
  • ✓4-pin peripheral Molex from the PC power supply, plus a separate 4-pin PWM control header

Design Highlights

Bykski B-PMD3-X angled product view showing both threaded ports in the clear pump top and the black housing

Clear PMMA pump top

The acrylic top comes installed on the black pump housing. Choose G1/4 fittings that match the type and size of tubing in your loop.

Bykski B-PMD3-X connector diagram showing the large Molex power plug and small PWM plug with numbered contacts

1 and 2 are the power leads. 3 is RPM feedback. 4 is PWM speed control.

Separate power and PWM leads

The large 4-pin Molex plug draws power from the PC power supply. The smaller 4-pin plug carries the PWM signal and reports pump speed.

Key Specifications

ModelB-PMD3-X
Pump typeDDC
Pump topClear PMMA acrylic
HousingBlack engineering plastic
Body dimensions62 × 62 × 53 mm
Inlet and outletG1/4
Rated supply12 V DC
Power connector4-pin peripheral Molex
Control connector4-pin PWM with tachometer feedback
Drive and shaftSine-wave drive, ceramic shaft
Maximum head6 m
Bykski B-PMD3-X manufacturer drawing showing the top and side dimensions of the pump body

Bykski’s pump body drawing. Dimensions are in millimeters.

Which Version Do I Need?

Bykski lists B-PMD3-X and B-PMD3-COV under separate model numbers. Check the full part number when replacing a PMD3 pump.

Bykski B-PMD3-XTHIS PAGE
Choose this pump with its preinstalled acrylic top when you’re supplying your own reservoir.
Choose this model if you want a pump with preinstalled aluminum armor.
Select a reservoir combo option on this listing to get the armored pump with a tube reservoir.

What's in the Box

Bykski B-PMD3-X pump with preinstalled acrylic top

Installation & Use

1
Check case clearance for the pump, reservoir, and fittings. For a supported pump-and-reservoir mount, Bykski shows the B-BKT-105 bracket with clear reservoir clamps.
2
Connect your reservoir to the pump inlet and plumb the loop with matching G1/4 fittings. For direct mounting with the B-CT50-MBK, remove the reservoir’s lower end cap before fitting it to the pump.
3
Plug the large 4-pin Molex connector into the power supply. Connect the smaller lead to a 4-pin PWM header for speed control and RPM feedback.
4
Fill the reservoir and prime the pump before applying power. Run only the pump while you top up the reservoir, bleed air, and check for leaks. Power the rest of the PC after the loop passes the leak test.

For a new loop, plan for a reservoir, compatible mounting hardware, G1/4 fittings, matching tubing, coolant, a radiator, and the water block or blocks for your hardware.

Bykski B-PMD3-X installation diagram showing a tube reservoir aligning with the pump top for direct mounting

Bykski’s direct-mount reservoir setup.

FAQ

Do I need a separate DDC pump top?

The clear acrylic pump top comes preinstalled and has G1/4 inlet and outlet ports.

What powers the pump and what controls its speed?

A 4-pin peripheral Molex connector supplies 12 V DC from the PC power supply. The separate 4-pin PWM connector handles speed control and RPM feedback.

Which reservoir can I mount directly?

Bykski shows its 50 mm B-CT50-MBK tube reservoir mounting directly to the pump top.

Do I need special tubing for the G1/4 ports?

Use G1/4 fittings on the pump. Choose the fitting type and size to match the tubing in your loop.

Notes
  • During filling, stop the pump before the reservoir empties. Running the pump dry can damage it.

FormulaMod Official Store

Recent Reviews
+