• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Hard Tube Bending Tool | Bykski B-PCTOOL-X, 12/14/16 mm OD

stars, based on ( 0 ) review
$24.81 piece
items available
Contact Us
FormulaMod Official Store
Bykski · B-PCTOOL-X

Adjustable bending tool for PC water-cooling hard tubes

The Bykski B-PCTOOL-X guides bends in rigid acrylic and PETG tubing for custom PC water cooling. Set the guide arms on the slotted base to match the angles and spacing you need. Then bend the softened tube against the guides to follow your planned route, including runs that need more than one bend.

Fits
12, 14, and 16 mm OD
Tubing
Acrylic and PETG
Guide arms
Repositionable

Fits / Use with

Use with rigid acrylic or PETG tubing in these outside diameters.

  • ✓12 mm OD
  • ✓14 mm OD
  • ✓16 mm OD

For the silicone bending insert, check the tube’s inside diameter separately.

Design Highlights

Bykski B-PCTOOL-X bending jig with a clear tube routed around two adjustable guide arms

Set the bend angle

Move a guide arm along the curved track and tighten it at the angle you need. The guide gives the softened tube a surface to bend against.

Bykski B-PCTOOL-X black base plate with straight slots, curved tracks, and measurement scales

Measure between bends

Use the distance scale and straight slots to position the guides when your route calls for a measured gap between bends.

Bykski B-PCTOOL-X setup diagram showing an offset bend traced in red in angled and top views

The red outline shows the tube path.

Set up an offset

Reposition the arms to make an offset when two fittings sit out of line. The guides can also be rearranged for successive bends on the same tube.

Key Specifications

ModelB-PCTOOL-X
ColorBlack
Tubing materialsRigid acrylic and PETG
Tube outside diameter12, 14, and 16 mm
Base (L × W × T)435 × 119 × 16 mm
Tool weight325 g
Bykski B-PCTOOL-X dimension drawing showing the length, width, and thickness of the base plate

Base plate dimensions in millimeters.

Which Bending Tool Do I Need?

Bykski B-PCTOOL-XTHIS PAGE
Choose the adjustable jig if you already have your heating and finishing tools and want to position the guides for your own tubing route.
Choose the kit if you need a size-matched bending mold, a bending insert, and a chamfering tool.

What's in the Box

1 × Bender base3 × Adjustable guide armsMounting hardware (screws and nuts)

How to Bend Hard Tubing

1
Measure the planned tube run. Set the jig on a stable work surface, then position and tighten the guide arms for the angle and spacing you need.
2
Slide a silicone bending insert sized for the tube’s inside diameter into the section you plan to bend.
3
Rotate the tube as you heat it so the bend area softens evenly. Keep the heat gun pointed away from the jig.
4
Guide the softened tube against the arms and hold it until the bend sets. Remove the insert once the tube holds its shape.
5
Trim to final length and chamfer the cut ends before fitting the tube into the loop.

Have rigid tubing, a heat gun, a matching silicone bending insert, a tube-cutting tool, and a chamfering tool on hand.

Bykski B-PCTOOL-X guide-arm setup diagram for two successive right-angle bends

Example guide-arm layout for two bends on one tube.

FAQ

Can I use the same bender for acrylic and PETG?

Yes. Use rigid acrylic or PETG with an outside diameter of 12, 14, or 16 mm.

Can I make two bends on a single tube?

Yes. Reposition the guide arms for the shape you need. The example above shows two right-angle bends on one tube.

Does the jig need to be bolted to a workbench?

It can sit on a stable work surface while you bend the tube.

Do I need a separate heat gun and bending insert?

Yes. The jig guides the tube after heating. Use a separate heat gun and a silicone insert sized for the tube’s inside diameter.

Notes
  • Not responsible for any hardware damage. Use at your own risk.

FormulaMod Official Store

Recent Reviews
+