• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

RTX 4070 Ti Water Block for MSI SUPRIM X 12G, Bykski N-MS4070TITRIO-X-V2 with Backplate & 5V ARGB Controller

stars, based on ( 0 ) review
items available
Contact Us
FormulaMod Official Store
Bykski · N-MS4070TITRIO-X-V2

Full-cover water block for MSI RTX 4070 Ti SUPRIM X 12G

The Bykski N-MS4070TITRIO-X-V2 replaces the stock cooler on the MSI GeForce RTX 4070 Ti SUPRIM X 12G with the matching PCB layout. Its nickel-plated copper cold plate cools the GPU core, memory, and voltage regulators in a custom liquid cooling loop. This set includes an aluminum backplate and a 5V ARGB lighting controller.

Fits
MSI SUPRIM X 12G PCB
Cold plate
Nickel-plated copper
Ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists this MSI custom PCB layout.

  • ✓MSI GeForce RTX 4070 Ti SUPRIM X 12G

Before ordering, verify the exact model on your card and match its PCB layout to Bykski’s reference layout.

Bykski N-MS4070TITRIO-X-V2 fit reference showing the MSI GeForce RTX 4070 Ti SUPRIM X 12G graphics card with its factory triple-fan cooler

The compatible MSI card shown with its factory cooler.

Design Highlights

Bykski N-MS4070TITRIO-X-V2 cold plate with machined coolant channels around the central microchannel fins

Full-cover copper cold plate

The cold plate draws heat from the GPU core, memory, and voltage regulators. A jet microchannel section sits over the GPU area.

Bykski N-MS4070TITRIO-X-V2 angled front view of the clear acrylic cover and the two threaded openings on the port terminal

Clear acrylic cover and G1/4 terminal

The clear cover leaves the coolant path visible. Use G1/4 fittings for the inlet and outlet and seal unused openings with the supplied stop plugs.

Bykski N-MS4070TITRIO-X-V2 black aluminum backplate with mounting holes

Passive aluminum backplate

The included black aluminum backplate mounts behind the PCB, outside the coolant path.

Key Specifications

ModelN-MS4070TITRIO-X-V2
Cold plateNickel-plated T2 copper
CoverClear acrylic
BackplateBlack aluminum
Cooling coverageGPU core, memory, and VRM
Port threadG1/4 inlet and outlet
Block (L × W × T)239.91 × 165.88 × 26.25 mm
Backplate (L × W × T)239.84 × 135.40 × 6.00 mm
Lighting5V 3-pin ARGB (RBW)
Lighting controllerIncluded
Bykski N-MS4070TITRIO-X-V2 dimension drawing with the block above and the backplate below

Bykski’s drawing shows the water block above and the backplate below. Measurements are in millimeters.

Which Version Do I Need?

Choose the water block by the exact model on your graphics card. MSI SUPRIM X and ASUS ProArt use different blocks.

N-MS4070TITRIO-X-V2THIS PAGE
Choose this set for the matching MSI RTX 4070 Ti SUPRIM X 12G PCB.
Check this block if your card is the ASUS ProArt GeForce RTX 4070 Ti OC.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set1 × 5V ARGB lighting controller

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the system, remove the graphics card, and take off the stock cooler. Clean the old thermal pads and paste off the PCB and GPU die.
2
Dry-fit the block to check the mounting holes. Apply the supplied thermal pads to the memory and power components marked in Bykski’s guide. Apply your own thermal paste to the GPU die.
3
Align the block and backplate with the PCB. Use the supplied mounting hardware and tighten the screws evenly.
4
Connect the tubing with G1/4 fittings, seal the unused openings with the stop plugs, and leak-test the loop before powering the graphics card.
5
Use the included lighting controller to run the LEDs independently. For motherboard sync, use a compatible Bykski sync cable to connect the block’s lighting lead to a 5V 3-pin ARGB header. Avoid the 12V 4-pin RGB header.

Use a custom loop with a pump, reservoir, radiator and fans, G1/4 tubing fittings, tubing, and coolant.

Bykski N-MS4070TITRIO-X-V2 numbered exploded diagram showing the block, thermal pads, PCB, mounting hardware, and backplate

Bykski’s assembly drawing. ① Block · ② Thermal pads · ③ PCB · ④ Washers · ⑤–⑥ Mounting screws · ⑦ Backplate · ⑧ Backplate screws.

FAQ

Which RTX 4070 Ti PCB does this water block fit?

Bykski lists the MSI GeForce RTX 4070 Ti SUPRIM X 12G. Match your card’s full model name and PCB layout before ordering.

What fittings do I need for the loop?

Use G1/4 fittings sized for your tubing. Use the included stop plugs to close unused terminal openings.

Can I use the lighting without a motherboard ARGB header?

Yes. The included controller can run the LEDs independently. For motherboard sync, use a compatible Bykski sync cable to connect the block’s lighting lead to a 5V 3-pin ARGB header. Avoid the 12V 4-pin RGB header.

Does coolant flow through the backplate?

The backplate mounts behind the PCB. Coolant circulates through the block on the front of the card.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.

FormulaMod Official Store

Recent Reviews
+