• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

RTX 4070 Ti Water Block for ASUS ProArt OC, Bykski N-AS4070TIPR-X with Backplate

stars, based on ( 0 ) review
€138.32 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-AS4070TIPR-X

Full-cover GPU water block for select ASUS ProArt cards

The Bykski N-AS4070TIPR-X replaces the stock cooler on the ASUS ProArt GeForce RTX 4070 Ti OC 12GB in a custom liquid cooling loop. Its full-cover copper cold plate cools the GPU core, memory, and voltage regulators. The block comes with a black aluminum backplate and uses G1/4 ports and 5V 3-pin ARGB lighting.

Fits
Select ASUS ProArt PCBs
Cold plate
Nickel-plated copper
Ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Match your exact ASUS model number.

  • ✓ASUS ProArt GeForce RTX 4070 Ti OC Edition 12GB (PROART-RTX4070TI-O12G)
  • ✓ASUS ProArt GeForce RTX 4080 SUPER OC Edition 16GB (PROART-RTX4080S-O16G)

Before ordering, confirm the model number on your card and verify its PCB layout and revision with FormulaMod support.

Bykski N-AS4070TIPR-X fit reference showing the ASUS ProArt GeForce RTX 4070 Ti OC with its stock cooler

ASUS ProArt GeForce RTX 4070 Ti OC with its factory cooler fitted.

Design Highlights

Bykski N-AS4070TIPR-X underside showing the shaped copper contact plate and mounting posts

One cold plate cools the GPU, memory, and VRM

The nickel-plated copper plate has raised contact surfaces for the GPU core, memory, and power delivery components. Coolant carries heat from the plate into the loop.

Bykski N-AS4070TIPR-X manufacturer illustration of the closely spaced cold plate fins

Jet microchannels

The 0.3 mm gaps between the fins give coolant a path through the area directly above the GPU core.

Bykski N-AS4070TIPR-X acrylic water block lit in red, purple, and blue

5V addressable lighting

The included 5V ARGB strip lights the clear acrylic top. Match it to a 5V 3-pin ARGB header or a compatible 5V controller.

Key Specifications

Model (SKU)N-AS4070TIPR-X
Cold plateNickel-plated high-purity T2 copper
TopClear PMMA acrylic
BackplateBlack aluminum, outside the coolant path
Cooling coverageGPU core, memory, and VRM
Inlet and outlet threadG1/4
Microchannel gap0.3 mm
Water block (L × W × T)219.82 × 145.92 × 26.97 mm
Backplate (L × W × T)219.82 × 115.92 × 6.00 mm
Lighting5V 3-pin addressable RGB (RBW)
Bykski N-AS4070TIPR-X dimension drawing with front and side views of the water block and backplate

Bykski dimensions in millimeters. The block is on top and the backplate is below.

Which Version Do I Need?

Bykski N-AS4070TIPR-XTHIS PAGE
Choose this block if your ASUS ProArt card matches one of the model numbers above and you’ve verified the PCB layout.
For the ASUS TUF Gaming RTX 4070 Ti 12GB (TUF-RTX4070TI-12G-GAMING), check the TUF block and its PCB compatibility list.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × 5V ARGB stripThermal pad setMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski N-AS4070TIPR-X black aluminum backplate showing the mounting holes

The included backplate mounts behind the graphics card PCB.

Installation & Use

1
Shut down and unplug the PC. Remove the graphics card, then take off its stock cooler and backplate. Clean the old thermal material from the GPU core, memory, and voltage regulators.
2
Check that the mounting holes line up. Apply thermal pads to the memory and the VRM components specified for your exact PCB. Apply a thin layer of your own thermal paste to the GPU die.
3
Align the block, PCB, and backplate. Fit the washers and screws in the positions shown for your PCB and tighten the screws gradually.
4
Connect the loop to the marked inlet and outlet using G1/4 fittings and seal unused ports with the stop plugs. For motherboard lighting sync, use a compatible adapter cable to connect to a 5V 3-pin ARGB header. You can also use a compatible 5V controller.
5
Fill the loop and leak-test it with only the pump powered. Check the ports and fittings for leaks before turning on the graphics card or other hardware.

You also need a pump and reservoir, radiator and fans, G1/4 fittings, matching tubing, and coolant.

Bykski N-AS4070TIPR-X exploded installation diagram showing the numbered block, thermal pads, graphics card PCB, washers, screws, and backplate

Bykski’s 4070 Ti OC mounting diagram. 1 block · 2 thermal pads · 3 graphics card PCB · 4 washers · 5 spring screws · 6 backplate · 7 backplate screws.

FAQ

How do I know if this RTX 4070 Ti water block fits my card?

Check for ASUS model number PROART-RTX4070TI-O12G and verify the PCB layout and revision before ordering.

Which fittings fit the water block?

Use G1/4 fittings that match your tubing and seal the unused ports with the supplied stop plugs.

Will a 12V 4-pin RGB header power the lighting?

Use a 5V 3-pin ARGB header or a compatible 5V controller. A 12V RGB header can damage the LEDs.

Does the included backplate carry coolant?

The black aluminum backplate mounts behind the PCB, outside the coolant path.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.

FormulaMod Official Store

Recent Reviews
+