• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Bykski CP-DWPB-X PWM Water Pump for Custom PC Loops, 1,400 L/h, 15 m Head

stars, based on ( 0 ) review
€89.34 piece
items available
Contact Us
FormulaMod Official Store
Bykski · CP-DWPB-X

PWM water pump for custom PC cooling loops

The Bykski CP-DWPB-X is a stand-alone pump that circulates coolant between the reservoir, water blocks, and radiator in a custom PC loop. It runs on 12 V DC power and supports PWM speed control with RPM feedback. Bykski specifies a maximum flow of 1,400 L/h and a maximum head of 15 m.

Fits
G1/4 fittings
Max flow
1,400 L/h
Max head
15 m
Motor power supply
12 V DC

Fittings & Mounting

  • ✓Use male G1/4 fittings sized for your tubing.
  • ✓Bykski shows radiator mounting with a B-BKT-105 bracket. Check whether you need to order the bracket separately.

Check clearance for the pump body, fittings, and tubing before choosing a mount.

Design Highlights

Bykski CP-DWPB-X upright pump showing the threaded top and side ports, knurled ring, and mounting tab

POM pump top with aluminum housing

The black POM top carries the two threaded coolant ports. The aluminum alloy housing surrounds the motor.

Bykski CP-DWPB-X diagram showing the larger Molex power connector and the separate PWM control connector

Bykski standard wiring diagram. (1–2) Motor power. (3) RPM feedback. (4) PWM speed control.

Separate power and speed control

Bykski’s standard wiring diagram shows a 4-pin Molex power connector and a separate four-position PWM connector for speed control and RPM feedback. Before ordering, check which connectors ship with the pump and whether they match your power supply and PWM controller.

Key Specifications

ModelCP-DWPB-X
Pump topBlack POM
Outer housingAluminum alloy
ShaftCeramic
Motor driveSine wave
Maximum flow1,400 L/h
Maximum head15 m
Rated voltage12 V DC
Rated current4 A
Input power48 W
Maximum input current5 A
Speed controlPWM with RPM feedback
Port threadsG1/4 female
Overall height95.50 mm
Width at mounting tab74.00 mm
Body diameter71.50 mm
Bykski CP-DWPB-X dimension drawing with side and top views showing the overall height, width, and body diameter

Bykski pump dimensions in millimeters.

Compare Bykski Pumps

Compare the published flow and head of these stand-alone pumps when sizing your loop.

Bykski CP-DWPB-XTHIS PAGE
Choose this model for the higher published limits of 1,400 L/h flow and 15 m head.
Choose the PARX model if its lower published limits of 330 L/h flow and 3 m head suit your loop.

What's in the Box

1 × CP-DWPB-X pump assembly with POM top and installed aluminum housing

Installation & Use

1
Check the space in your case and secure the pump to its mount. For radiator mounting, follow Bykski’s B-BKT-105 bracket diagram.
2
Confirm which pump port is the inlet before connecting tubing. Route the reservoir outlet directly to the pump inlet, then connect the pump outlet to the rest of the loop.
3
Match the motor power connector to your power supply. Connect the speed-control lead to a compatible PWM header for speed adjustment and RPM feedback.
4
Fill the reservoir and prime the pump with coolant before applying power. Run only the pump while you top up the reservoir and bleed air from the loop.
5
Inspect the fittings and joints for leaks before powering on the rest of the PC.

For a new loop, you also need a separate reservoir, G1/4 fittings, matching tubing, coolant, water blocks, a radiator, and fans.

Bykski CP-DWPB-X exploded mounting drawing showing the pump and B-BKT-105 bracket next to a radiator

Bykski mounting diagram. The B-BKT-105 bracket sits between the pump’s mounting tab and the radiator.

FAQ

Will the pump move 1,400 L/h in my loop?

That is Bykski’s maximum flow figure. Actual flow depends on the resistance of your loop.

What are the pump’s power requirements?

The motor is rated for 12 V DC and has a maximum input current of 5 A. Check that your power supply matches the pump’s power connector before connecting it.

Can I adjust the pump speed?

Yes. A compatible PWM header can control the pump speed and read RPM.

Which fittings fit the pump top?

Use male G1/4 fittings. Match the tubing side of each fitting to the tubing you use.

Can I power the pump before filling the loop?

Prime the pump with coolant before turning it on. Keep the reservoir topped up while you bleed the loop to prevent dry running.

FormulaMod Official Store

Recent Reviews
+