• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

12/14/16 mm OD Hard Tube Fitting Kit, Bykski BY-HTK with G1/4 Rotary Elbows

stars, based on ( 0 ) review
items available
Contact Us
FormulaMod Official Store
Bykski · BY-HTK

Hard tube fitting kit for custom PC water cooling

The Bykski BY-HTK kit connects acrylic hard tubing to G1/4 ports in a custom PC water cooling loop. Each kit pairs six 500 mm tubes with fittings sized for the tube’s outside diameter. Use the 90° rotary elbows to redirect tubing runs at component ports and the stop plugs to close unused ports.

Fits
G1/4 ports
Tube OD
12, 14, or 16 mm
Tube length
500 mm each
Elbows
90° rotary

Fits

For custom loops with G1/4 female ports.

  • ✓12 mm OD acrylic hard tube with 12 mm OD fittings
  • ✓14 mm OD acrylic hard tube with 14 mm OD fittings
  • ✓16 mm OD acrylic hard tube with 16 mm OD fittings

Match the fitting to the tube’s outside diameter. Soft tubing requires its own fittings.

Design Highlights

Bykski BY-HTK close-up of the silver anti-off hard tube fitting with a blue insert and knurled collar

Straight fittings matched to the tube

The anti-off straight fittings grip the acrylic tube at one end and screw into a G1/4 port at the other.

Bykski BY-HTK silver 90-degree rotary elbow showing the female opening and male thread

Turn a run at the port

The 90° rotary elbow changes the direction of a run at the component. Aim the elbow, then screw the straight hard tube fitting into its female end.

Key Specifications

Kit modelBY-HTK
Tube materialClear acrylic
Tube length500 mm per tube
Tube OD × ID12 × 8 mm, 14 × 10 mm, or 16 × 12 mm
Straight fitting threadG1/4 male
Elbow angle and thread90° rotary, G1/4 male to female
Stop plug threadG1/4 male
Hardware colorsBlack, Silver, Gold, White
Straight fitting body diameter21.2 mm for 12 mm OD, 23.2 mm for 14 mm OD, 25.2 mm for 16 mm OD (from original kit drawings)
Elbow height with thread32.69 mm (from original kit drawings)
Stop plug diameter × height with thread18.22 × 9.70 mm (from original kit drawings)
Bykski BY-HTK tube drawings showing the 500 mm length and the outside and inside diameters for all three tube sizes

Tube dimensions from top to bottom for the 12, 14, and 16 mm OD options.

Which Version Do I Need?

Choose the kit for a new run that needs tubing and several kinds of fittings. For a smaller change, check the outside diameter of the tubing already in your loop.

Bykski BY-HTK kitTHIS PAGE
Get acrylic tubes, matched straight fittings, rotary elbows, and stop plugs together.
For matching replacements, check the available color and outside diameter combinations.
Choose the same outside diameter when adding tubing. Each pack contains two tubes.

What's in the Box

6 × 500 mm clear acrylic hard tubes in the selected OD8 × G1/4 anti-off straight fittings in the selected OD4 × G1/4 90° rotary elbows2 × G1/4 stop plugs
Bykski BY-HTK black hardware layout with two stop plugs above four rotary elbows and eight straight fittings

Black kit hardware shown. Six acrylic tubes are also included.

Installation & Use

1
Plan each tube run and count the fittings and elbows you’ll need. Choose the kit by tube outside diameter.
2
Cut the acrylic tube to length and deburr the inside and outside of each cut end.
3
Thread the straight fittings into the G1/4 ports or the female ends of the rotary elbows. Use the stop plugs on unused ports.
4
Align each tube so it sits without tension. Seat it fully in the fitting and tighten the collar by hand.
5
Leak-test the assembled loop with the rest of the PC unpowered. Check each joint before powering the system.

You’ll need acrylic cutting and deburring tools. For heated bends, use a heat gun, a bending tool, and a silicone insert sized to the tube’s inside diameter. Water blocks, a radiator, a pump, a reservoir, and coolant are not included.

Bykski BY-HTK clear acrylic hard tubes with the open ends visible

FAQ

Which kit fits my 12 mm OD acrylic tube?

Choose the 12 mm OD kit. Each kit comes with straight fittings for the one outside diameter you select.

Does the 90° rotary elbow connect directly to the tube?

The elbow has male and female G1/4 threads. Screw a straight hard tube fitting into the female side to connect the tube.

Can I use these fittings with soft tubing?

Soft tubing needs fittings made for soft tube. These straight fittings are sized for rigid tubing.

How long are the tubes, and how many come in the kit?

Each kit includes six 500 mm acrylic tubes in your selected outside diameter.

Notes
  • 1. The color between different kind of Fitting might have difference. (For example, the gold color for hard tube fitting might be different with the gold color of 90 degree fitting.)
  • 2. Due to the difference between different monitors, the color of pictures and the real object will be slightly different.
  • 3.In case of upgrading to the appearance and structure, no further notice, the real object shall prevail.

FormulaMod Official Store

Recent Reviews
+