• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Manli Gallardo RTX 5090D OC 32GB GPU Water Block with Backplate and ARGB | Bykski N-ML5090GR-X

stars, based on ( 0 ) review
items available
Contact Us
FormulaMod Official Store
Bykski · N-ML5090GR-X

Full-cover water block for the Manli Gallardo RTX 5090D OC

The Bykski N-ML5090GR-X replaces the stock cooler on the Manli Gallardo GeForce RTX 5090D OC 32GB for use in a custom liquid cooling loop. Its T2 copper cold plate draws heat from the GPU core, memory, and voltage regulators. The bundle includes a black aluminum backplate and a 5V ARGB lighting controller.

Fits
Manli Gallardo RTX 5090D OC 32GB
Cold plate
T2 copper
Ports
G1/4 inlet and outlet
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists this graphics card for the N-ML5090GR-X.

  • ✓Manli Gallardo GeForce RTX 5090D OC 32GB (Starship)

Check your card label for Manli model M-N509DGO/D732G-M3626. Before ordering, compare your PCB layout and mounting holes with the board shown in Bykski’s installation drawing below.

Bykski N-ML5090GR-X compatibility reference showing the Manli Gallardo RTX 5090D OC graphics card with its three stock fans

Manli’s product image of the card with its stock cooler.

Design Highlights

Bykski N-ML5090GR-X coolant-flow diagram through the water block and across the central microchannels

Bykski’s coolant-flow illustration.

Coolant path across the cold plate

Bykski specifies a 0.3 mm jet microchannel design with up to 56 channels.

Bykski N-ML5090GR-X front window on the black water block lit in purple and blue

5V addressable lighting

The clear window shows the coolant channels and the built-in ARGB lighting. Use the included controller if you prefer to run the lighting without motherboard sync.

Bykski N-ML5090GR-X separate black backplate with mounting holes and a cutout along one end

Separate aluminum backplate

The backplate screws onto the rear of the graphics card PCB. The coolant connections are on the water block.

Key Specifications

ModelN-ML5090GR-X
CoverageGPU core, memory, and voltage regulators
Cold plateT2 copper
Copper plate158.451 mm long × 6 mm thick
Copper under the channels0.35 mm at the point shown in Bykski’s cross section
Microchannels0.3 mm jet microchannel design, up to 56 channels
Channel surface area10,962.06 mm²
BackplateBlack aluminum
Water block (L × W × D)254.36 × 127.82 × 29.59 mm
Backplate (L × W × D)254.35 × 127.82 × 22.60 mm
Inlet and outlet threadG1/4
Lighting5V 3-pin ARGB (RBW), controller included
Bykski N-ML5090GR-X dimension drawing with face and side views of the water block and separate backplate

Bykski’s dimension drawing. Water block above, backplate below. All measurements in millimeters.

Which Version Do I Need?

Check the exact model on your card label before choosing a Gallardo water block.

Bykski N-ML5090GR-XTHIS PAGE
Choose this ARGB block and controller bundle for the listed Manli Gallardo RTX 5090D OC 32GB PCB.
Compare this metal/POM block for the same 5090D Gallardo or for the Manli Gallardo RTX 5090 OC 32GB or ZOTAC GeForce RTX 5090D 32GB SOLID OC listed for the SR-V2.

What's in the Box

1 × full-cover GPU water block1 × black aluminum backplateThermal pad setMounting hardware set1 × 5V ARGB lighting controller2 × G1/4 stop plugs

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski N-ML5090GR-X exploded installation drawing of the block, pads, graphics card PCB, backplate, and screws

① Water block · ② Thermal pads · ③ Your graphics card PCB · ④ Mounting screws · ⑤ Backplate · ⑥ Backplate screws.

Installation & Use

1
Power down the PC, remove the graphics card, and detach the stock cooler. Clean the old thermal material from the contact surfaces.
2
Cut the supplied thermal pads to fit and place them on the memory and power components shown in Bykski’s placement drawing. Apply your own thermal paste to the GPU die.
3
Align the water block with the PCB mounting holes. Fasten the block and backplate as shown in the exploded drawing. If the holes do not line up, stop and recheck the PCB before tightening.
4
Connect the inlet and outlet to your loop with G1/4 fittings that match your tubing. Seal any unused ports.
5
Connect the lighting to the supplied controller or a compatible 5V 3-pin ARGB sync connection. Keep it away from 12V 4-pin RGB headers.
6
Fill the loop and power only the pump for the leak test. Inspect every fitting for leaks before powering the graphics card.

For the loop, you’ll also need a pump, reservoir, radiator, radiator fans, G1/4 tubing fittings, tubing, and coolant.

Bykski N-ML5090GR-X PCB diagram with shaded pad locations around the GPU die

Bykski’s placement drawing. The shaded regions around the GPU mark the memory and power components that take pads.

FAQ

Which RTX model is this water block for?

This version is for the Manli Gallardo GeForce RTX 5090D OC 32GB. Check the Manli model number and compare the PCB layout before ordering.

What fittings does the block use?

The inlet and outlet use G1/4 threads. Choose fittings that also match the type and size of your tubing.

Can I run the lighting without motherboard sync?

Yes. The included lighting controller can run the block’s 5V ARGB lighting on its own.

Where do the thermal pads go?

Place the supplied pads on the memory and power components marked in Bykski’s installation drawing.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.

FormulaMod Official Store

Recent Reviews
+