• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Gigabyte RTX 4090 WINDFORCE 24G Water Block (GV-N4090WF3-24GD) | Bykski N-GV4090WF-X

stars, based on ( 1 ) reviews
€133.47 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-GV4090WF-X

Full-cover water block for Gigabyte RTX 4090 WINDFORCE 24G

The Bykski N-GV4090WF-X replaces the stock cooler on the Gigabyte GeForce RTX 4090 WINDFORCE 24G (GV-N4090WF3-24GD) so you can cool the card in a custom liquid loop. A nickel-plated copper cold plate transfers heat from the GPU, memory, and voltage regulators to the coolant. An aluminum backplate mounts behind the circuit board.

Fits
GV-N4090WF3-24GD
Ports
G1/4
Lighting
5V 3-pin ARGB
Backplate
Black aluminum

Compatibility

Match the exact Gigabyte card code.

  • ✓Gigabyte GeForce RTX 4090 WINDFORCE 24G (GV-N4090WF3-24GD)

The WINDFORCE V2 24G has a separate card code (GV-N4090WF3V2-24GD). For that card, check water block listings for your exact PCB.

Before ordering, verify the card code and match your PCB layout to the board shown in Bykski’s compatibility diagram in the product gallery.

Bykski N-GV4090WF-X compatibility photo of the Gigabyte RTX 4090 WINDFORCE 24G with its three-fan stock cooler

Gigabyte RTX 4090 WINDFORCE 24G with its factory cooler, shown for identification.

Design Highlights

Bykski N-GV4090WF-X underside showing the shaped cold plate contact surfaces and mounting posts

Cooling across the board

The cold plate has separate contact surfaces for the graphics chip, memory, and power circuitry. Coolant passes through jet microchannels with 0.5 mm spacing.

Bykski N-GV4090WF-X clear top illuminated in red, purple, and blue

Clear top with addressable lighting

The clear acrylic top exposes the coolant channels. The block uses 5V addressable lighting (RBW).

Key Specifications

ModelN-GV4090WF-X
Cold plateNickel-plated T2 copper
TopClear acrylic (PMMA)
BackplateBlack aluminum, passive
Inlet and outlet threadG1/4
Microchannel spacing0.5 mm
Water block (L × W × T)229.79 × 166.92 × 20.00 mm
Backplate (L × W × T)229.79 × 136.92 × 6.00 mm
Lighting5V 3-pin ARGB (RBW)
Bykski N-GV4090WF-X water block dimension drawing with IN and OUT port markings

Bykski water block drawing. Measurements are in millimeters.

Which Version Do I Need?

Check the card’s model label first, then choose the block for its PCB.

Bykski N-GV4090WF-XTHIS PAGE
Choose this for the original WINDFORCE 24G if you want a clear acrylic top and 5V ARGB.
Choose this for the original WINDFORCE 24G if you prefer aluminum armor around the front and back.
Choose this separate block for the NVIDIA GeForce RTX 4090 Founders Edition PCB.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × thermal pad set1 × mounting hardware set5V 3-pin ARGB motherboard adapter cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski N-GV4090WF-X clear GPU block beside the included black aluminum backplate

Installation & Use

1
Power off the system, remove the graphics card, and take off the stock cooler.
2
Remove the old thermal pads and clean off the old paste. Test-fit the block and check the mounting holes.
3
Apply the thermal pads at the indicated memory and power circuitry contact points. Spread your own thermal paste over the GPU die.
4
Align the block with the PCB and secure it with the matching washers and spring screws. Fit the backplate and tighten its screws gently.
5
Connect the loop with G1/4 fittings. Follow the inlet and outlet markings and seal any unused ports.
6
Leak-test the loop with the graphics card unpowered.

For the rest of the loop, you’ll need a pump, radiator, G1/4 fittings, tubing, and coolant.

FAQ

Which Gigabyte RTX 4090 does this water block fit?

Match the original WINDFORCE 24G card code GV-N4090WF3-24GD and check the PCB layout before ordering.

Which water block should I use for an RTX 4090 Founders Edition?

Look for a block listed for the Founders Edition PCB, such as the Barrow BS-NVG4090-PA.

Which fittings do I need?

Use G1/4 fittings at the inlet and outlet. Choose fittings that match your tubing.

How do I connect the lighting?

For motherboard sync, connect the lighting to a 5V 3-pin ARGB header using the included adapter cable if the plug does not match the header. You can also use a compatible 5V RBW controller. A 12V 4-pin RGB header can damage the LEDs.

Does the backplate carry coolant?

The included aluminum backplate is passive. Coolant flows through the front block.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.
Recent Reviews ( 1 )
By
TAGE
Friday, 09 December 2022
Fantastic block. easy to install.Instructions aren't super clear but also it's not hard; follow the pictures.One thing missing from the instructions is; you need to remove a corner screw of the PCI bracket; so that the whole block can fit.Also the matching stanfoff of the backplate for this particular pci bracket screw should be removed.
+