• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

NVIDIA H200 141GB Water Block – Bykski N-H200-SR-QH, Vacuum-Brazed with Backplate

stars, based on ( 0 ) review
€342.57 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-H200-SR-QH

Full-cover water block for NVIDIA H200 141GB

The Bykski N-H200-SR-QH is a full-cover water block and backplate kit listed for NVIDIA H200 141GB. In a custom liquid-cooling loop, its cold plate transfers heat from the GPU die, memory, and voltage regulation components to the coolant, which carries the heat to a separate radiator. Confirm your card part number and PCB revision before ordering.

Listed fit
H200 141GB · verify PCB
Cold plate
Nickel-plated copper
Port thread
G1/4

Compatibility

Model listed by Bykski

  • ✓NVIDIA H200 141GB

H200 models with different board layouts can share the same 141GB capacity. Confirm compatibility for your exact card part number and PCB revision before ordering.

NVIDIA H200 NVL PCIe card with its factory passive heatsink, vented bracket, and edge connector

NVIDIA H200 NVL exterior reference (Lenovo Press). Check the part number and PCB revision on your card.

Design Highlights

Bykski N-H200-SR-QH underside with raised copper contact surfaces and mounting posts

One cold plate for the GPU, memory, and VRM

The nickel-plated, oxygen-free copper plate has raised contact surfaces for the GPU die, memory, and voltage regulation components. Coolant carries their heat away through the block.

Bykski N-H200-SR-QH silver water block with two hose barbs at one end

Vacuum-brazed block with end-mounted fittings

The block is assembled by vacuum brazing. Its two hose barbs come installed at the same end, so plan your tube routing with clearance alongside that end of the card.

Key Specifications

ModelN-H200-SR-QH
Cooling typeFull-cover GPU water block for a custom loop
Cold plateNickel-plated oxygen-free copper
ConstructionVacuum brazing
BackplateAluminum alloy
Block dimensions266.63 × 98.24 × 19.10 mm
Backplate dimensions182.33 × 94.78 × 3.86 mm
Port threadG1/4 female
Installed fittings2 hose barbs
Bykski N-H200-SR-QH dimension drawing for the water block and backplate

Manufacturer drawing of the water block (top) and backplate (bottom). Dimensions are in millimeters.

Which Version Do I Need?

Confirm your board’s compatibility with each cooler before choosing a standalone block or all-in-one kit.

Bykski N-H200-SR-QHTHIS PAGE
Choose this vacuum-brazed block and backplate if you have a custom loop or plan to assemble one.
Choose the standard 360 mm kit if you want the pump, tubing, and radiator supplied together.
Compare this standalone block and backplate if you plan to use a separate pump and radiator.
Choose the single-block 360 mm configuration for one card or compare the dual-block 480 mm configuration for two.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate5 × 1.5 mm thermal pad strips4 × 0.5 mm washers4 × M2 × 5 mm spring screws6 × M2 × 10.3 mm backplate screws

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Bykski N-H200-SR-QH backplate with mounting holes and edge cutouts

Installation & Use

1
Confirm compatibility using your card part number and PCB revision. Remove the stock heatsink and clean off the old paste and pads.
2
Place the 1.5 mm thermal pads where the cold plate has matching contact surfaces. Apply your own GPU thermal paste to the die.
3
Align the block and backplate with the PCB holes. Fit the washers and mounting screws as shown, then tighten evenly.
4
Connect tubing that matches the preinstalled barbs. Fill and bleed the loop.
5
Run the pump on its own to check for leaks with the GPU and the rest of the system powered off. Power the GPU only after the loop passes the leak test.

You’ll also need a pump, radiator, reservoir or pump-reservoir combo, coolant, compatible tubing, and any additional G1/4 fittings required by your loop.

Bykski N-H200-SR-QH exploded assembly drawing showing the numbered block, pads, customer PCB, backplate, and hardware

Assembly order (manufacturer drawing). 1 Water block · 2 Thermal pads · 3 Your graphics card PCB · 4 Washers · 5 Spring screws · 6 Backplate · 7 Backplate screws.

FAQ

How do I tell H200 NVL and H200 SXM apart?

NVIDIA lists both with 141GB of memory. H200 NVL is a PCIe add-in card. H200 SXM is a module used in HGX systems.

Does this water block cool the VRM?

Yes. The cold plate draws heat from the voltage regulation components as well as the GPU die and memory.

Do I need a separate pump and radiator?

Yes. This block connects to a custom loop that circulates coolant with a pump and releases heat through a radiator.

Which fittings and tubing should I use?

The block has G1/4 female threads and two preinstalled hose barbs. Match the tubing to the barbs on your block.

How much space should I leave in the case?

Use the block dimensions to check clearance at the card. Leave space for the tubes to bend at the fitting end and check the case mounts for your chosen radiator.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The product does NOT include printed instructions. See the exploded assembly drawing in Installation & Use.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
  • This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.

FormulaMod Official Store

Recent Reviews
+