• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

RTX 3070 Water Block for Palit GamingPro OC | Bykski N-PT3070PRO-X

stars, based on ( 1 ) reviews
€135.59 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-PT3070PRO-X

Full-cover water block for Palit RTX 3070 GamingPro OC

The Bykski N-PT3070PRO-X replaces the stock cooler on the Palit GeForce RTX 3070 GamingPro OC and the other PCB layouts listed below. Its copper cold plate transfers heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop. This version includes an aluminum backplate and 5V addressable lighting.

Fits
Palit RTX 3070 GamingPro OC
Ports
G1/4
Lighting
5V 3-pin ARGB
Backplate
Black aluminum

Compatibility

This block fits the specified PCB layouts for these cards.

  • ✓Palit GeForce RTX 3070 GamingPro OC
  • ✓Palit GeForce RTX 3060 Ti GamingPro
  • ✓Leadtek WinFast RTX 3070 LIFE ES 8G
  • ✓Yeston GeForce RTX 3070 8G
  • ✓PNY GeForce RTX 3070 XLR8 Gaming REVEL EPIC-X RGB Triple Fan (VCG30708TFXPPB)
  • ✓Gainward GeForce RTX 3070 Phoenix GS

Before ordering, verify your exact card model and PCB layout, including the mounting holes and component positions.

Bykski N-PT3070PRO-X compatibility reference showing the bare Palit GeForce RTX 3070 GamingPro OC PCB, its mounting holes, and component layout

Palit GeForce RTX 3070 GamingPro OC PCB. Photo by Overclockers.ru.

Design Highlights

Bykski N-PT3070PRO-X underside showing the copper cold plate and raised contact areas

Full-cover copper cold plate

The copper cold plate has separate contact areas for the GPU core, memory, and VRM. Thermal pads bridge the matching memory and VRM contact points.

Bykski N-PT3070PRO-X close-up illustration of the jet microchannel fins

Jet microchannels over the GPU core

The three-layer block guides coolant through jet microchannels over the GPU core. Bykski’s drawing for the N-PT3070PRO-X specifies a 9 mm copper plate and a 0.5 mm microchannel gap.

Bykski N-PT3070PRO-X acrylic cover lit in purple, blue, and cyan

Addressable lighting under clear acrylic

The 5V ARGB strip lights the clear acrylic cover and the visible coolant channels. Connect it to the motherboard with a 5V 3-pin ARGB adapter cable or use a compatible 5V controller.

Key Specifications

ModelN-PT3070PRO-X
Cold plateT2 copper cold plate
TopClear acrylic
BackplateBlack aluminum, outside the coolant path
Cooling coverageGPU core, memory, and VRM
Port threadG1/4 inlet and outlet
Water block (L × W × T)189.47 × 126.80 × 28.00 mm
Lighting5V 3-pin ARGB (RBW)
Bykski N-PT3070PRO-X manufacturer drawing showing face and side dimensions of the water block

Manufacturer’s water block dimensions in millimeters.

Which Version Do I Need?

Check the manufacturer and exact model on your card before choosing a block.

Bykski N-PT3070PRO-XTHIS PAGE
Choose this block for a listed card with the matching PCB layout.
Check this block if you have an NVIDIA GeForce RTX 3070 Founders Edition.

What's in the Box

1 × full-cover GPU water block1 × black aluminum backplate2 × G1/4 stop plugs1 × mounting hardware setThermal pads1 × 5V ARGB LED strip

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the system and remove the graphics card. Remove the stock cooler and clean off the old thermal paste and pads.
2
Check that the block’s mounting holes and contact areas line up with the PCB. Place thermal pads on the memory and VRM contact points shown in the installation diagram. Apply your own thermal paste to the GPU core.
3
Align the block, PCB, and backplate. Install the insulation washers and spring screws as shown, then tighten the spring screws gradually in a diagonal pattern and secure the backplate.
4
Connect the marked inlet and outlet to your loop with G1/4 fittings. Seal the unused openings with the stop plugs.
5
For the lighting, use a 5V 3-pin ARGB adapter cable to reach the motherboard header, or connect the strip to a compatible 5V controller. Fill and leak-test the loop before powering the graphics card.

For the loop, you’ll also need a pump, radiator, tubing, coolant, and G1/4 fittings.

Bykski N-PT3070PRO-X numbered exploded view of the block, pads, GPU PCB, backplate, and mounting hardware

1 Water block · 2 Thermal pads · 3 Graphics card PCB · 4 Insulation washers · 5 Spring screws · 6 Backplate · 7 Backplate screws

FAQ

What thermal pad thickness does the Bykski block use?

Bykski’s installation drawing specifies 1.8 mm pads for the N-PT3070PRO-X water block. Apply them at the marked memory and VRM contact points.

What fittings do I need?

Use G1/4 fittings that match your tubing. Use the supplied stop plugs to seal unused ports.

How do I connect the ARGB lighting?

Use a 5V 3-pin ARGB adapter cable for the motherboard header or a compatible 5V controller. A 12V 4-pin RGB header can damage the strip.

What else do I need to water-cool my RTX 3070?

This block connects to a custom loop with a pump, radiator, tubing, G1/4 fittings, and coolant.

Notes
  • This is a repair or replace only item. Returns not accepted on compatibility issues or if block has had water/fluid run through it.
  • Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item. Product does NOT come with English instructions. Please see product gallery images for install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points with the exception of the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
  • Not responsible for any damage caused by or when using this product. Please use at your own risk.
Recent Reviews ( 1 )
By
RICHARD A JOHN
Sunday, 31 July 2022
its a great GPU Block it fit straight out of the box and my system looks awesome now
+