• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

PowerColor RX 7900 XTX Red Devil Water Block with Backplate | Bykski A-PC7900XTXDEVIL-X

stars, based on ( 0 ) review
$146.41 set
items available
Contact Us
FormulaMod Official Store
Bykski · A-PC7900XTXDEVIL-X

Full-cover water block for the PowerColor Red Devil RX 7900 XTX

The Bykski A-PC7900XTXDEVIL-X is a full-cover water block for the PowerColor Red Devil Radeon RX 7900 XTX 24GB with Bykski’s specified PCB layout and three 8-pin PCIe power connectors. It replaces the stock cooler and connects to a custom loop to cool the GPU core, memory, and voltage regulators. It includes an aluminum backplate and 5V addressable RGB lighting.

Fits
Red Devil RX 7900 XTX 24GB
Cold plate
Copper
Ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists the following Red Devil PCB layout.

  • ✓PowerColor Red Devil Radeon RX 7900 XTX 24GB (RX7900XTX 24G-E/OC), with three 8-pin PCIe power connectors

The PowerColor Hellhound (RX7900XTX 24G-L/OC) and PowerColor reference card (RX7900XTX 24G) each have two 8-pin power connectors.

Before ordering, confirm the model on your card and compare the full PCB, including the mounting holes and component layout, with Bykski’s bare PCB reference in the sixth image of the product gallery.

PowerColor Red Devil RX 7900 XTX 24GB graphics card with its stock triple-fan cooler.

PowerColor Red Devil RX 7900 XTX 24GB with its original cooler.

Design Highlights

Bykski A-PC7900XTXDEVIL-X manufacturer diagram with a color overlay showing the coolant path from the inlet to the outlet

Bykski’s coolant flow illustration.

Full-cover cooling

The cold plate has contact areas for the GPU die, memory, and voltage regulators. Coolant carries heat from these areas to the radiator in your loop.

Bykski A-PC7900XTXDEVIL-X water block showing the coolant channels through its clear acrylic top

Jet microchannels over the GPU

Coolant passes through the fine channels in the cold plate above the GPU core. The clear acrylic top leaves the machined flow path visible.

Bykski A-PC7900XTXDEVIL-X water block illuminated in red, purple, and blue through its acrylic top

5V addressable RGB

The included RBW light strip illuminates the clear top. Connect it to a 5V 3-pin ARGB header using the lighting sync cable.

Key Specifications

ModelA-PC7900XTXDEVIL-X
Cold plateCopper
TopClear acrylic
BackplateBlack aluminum
Cooling coverageGPU core, memory, and VRM
Port threadG1/4 inlet and outlet
Water block (L × W × T)285.29 × 157.46 × 23.15 mm
Backplate (L × W × T)284.89 × 127.46 × 6.00 mm
Lighting5V 3-pin ARGB (RBW)
Bykski A-PC7900XTXDEVIL-X dimension drawings of the water block above and the backplate below, each with a side view

Bykski dimensions in millimeters. Water block above, backplate below.

Which Version Do I Need?

Match the water block to the card maker and the specific RX 7900 XTX model on your label.

A-PC7900XTXDEVIL-XTHIS PAGE
Choose this block for the matching PowerColor Red Devil RX 7900 XTX 24GB PCB.
Check this block for the ASRock Radeon RX 7900 XTX Taichi 24GB OC.
Check this block for the Sapphire Radeon RX 7900 XTX Nitro+.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware setThermal pad set1 × 5V ARGB light strip1 × lighting sync cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski A-PC7900XTXDEVIL-X black aluminum backplate showing its mounting holes and grooved corners

The included backplate mounts behind the graphics card PCB.

Installation & Use

1
Power off the system and remove the graphics card. Remove the stock cooler and clean away the old thermal materials.
2
Cut the pads to fit the memory and voltage regulator locations shown in Bykski’s guide. Apply your own thermal paste to the GPU die.
3
Align the water block with the PCB holes and secure the block and backplate using the mounting hardware. If the holes fail to line up, stop and recheck the PCB.
4
Connect the loop to the marked inlet and outlet with G1/4 fittings. Use the stop plugs to seal the unused ports.
5
To connect the lighting, align the cable arrow with the +5V pin on a 3-pin ARGB header.
6
Fill and leak-test the loop with the graphics card unpowered.

You also need a pump and reservoir, a radiator, coolant, tubing, and G1/4 fittings sized for that tubing.

Bykski A-PC7900XTXDEVIL-X exploded assembly drawing showing the water block above the pads and PCB, with the backplate and fasteners below

1 Water block · 2 Thermal pads · 3 Graphics card PCB · 4 Block fasteners · 5 Backplate · 6 Backplate screws.

FAQ

Is this the water block used on the RX 7900 XTX Liquid Devil?

PowerColor ships the Liquid Devil with a factory-fitted EK water block. Bykski lists this block for the Red Devil PCB in its compatibility guide.

How long is the water block?

The block is 285.29 mm long, 157.46 mm wide, and 23.15 mm thick. Use the dimension drawing when planning clearance.

What fittings should I use?

The inlet and outlet take G1/4 fittings. Choose fittings that match the type and diameter of your tubing.

Which motherboard header powers the lighting?

Use a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the LEDs.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.

FormulaMod Official Store

Recent Reviews
+