• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Gigabyte RTX 5090 Gaming OC GPU Water Block with Backplate | Bykski N-GV5090DWF-X

stars, based on ( 0 ) review
€171.10 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-GV5090DWF-X

Full-cover GPU water block with end-mounted ports

The Bykski N-GV5090DWF-X is a full-cover water block for a custom loop on supported Gigabyte cards, including the GeForce RTX 5090 GAMING OC 32G. Its nickel-plated copper cold plate transfers heat from the GPU, memory, and voltage regulators to the coolant. The block has end-mounted G1/4 ports and comes with an aluminum backplate.

Fits
Gigabyte RTX 5090 GAMING OC 32G and select RTX 5090 D cards
Ports
End-mounted G1/4
Backplate
Black aluminum
Lighting
5V ARGB (RBW)

Compatibility

Bykski lists these specific Gigabyte card layouts for the N-GV5090DWF-X.

  • ✓Gigabyte GeForce RTX 5090 GAMING OC 32G (GV-N5090GAMING OC-32GD)
  • ✓Gigabyte GeForce RTX 5090 D GAMING OC 32G (GV-N509DGAMING OC-32GD)
  • ✓Gigabyte GeForce RTX 5090 D WINDFORCE 32G (GV-N509DWF3-32GD)

Check the model number on your card and match the PCB layout, including the screw holes and component positions, to Bykski’s reference before ordering.

Bykski N-GV5090DWF-X compatibility photo of a bare Gigabyte RTX 5090-series PCB with its I/O bracket and GPU die

Bykski’s Gigabyte PCB reference. Compare the mounting holes, component locations, and board outline.

Design Highlights

Bykski N-GV5090DWF-X front view of the acrylic window and clear port terminal at the short end

End-mounted ports and acrylic window

The inlet and outlet sit at the short end of the block. Use G1/4 fittings there and check the clearance you need for the fittings and tubing. The acrylic window gives you a view of the coolant channels.

Bykski N-GV5090DWF-X illustration showing the cold plate microchannel fins

Bykski’s close-up illustration of the microchannels.

Copper cold plate with microchannels

The nickel-plated copper cold plate has separate contact areas for the GPU die, memory, and voltage regulators. Coolant passes through 0.3 mm microchannels over the GPU contact area.

Bykski N-GV5090DWF-X black aluminum backplate with mounting holes and a cutout at one end

Separate aluminum backplate

The included black aluminum backplate bolts to the rear of the graphics card. It is passive and sits outside the coolant path.

Key Specifications

ModelN-GV5090DWF-X
Cold plateNickel-plated T2 copper
Copper plate design (Bykski specification)6 mm
Microchannel design0.3 mm
WindowClear acrylic
BackplatePassive black aluminum
Threads and port locationG1/4 inlet and outlet at the short end
Water block (L × W × D)254.88 × 136.05 × 33.65 mm
Backplate envelope (L × W × D)254.88 × 136.05 × 25.75 mm
Lighting5V 3-pin addressable RGB (RBW)
Bykski N-GV5090DWF-X dimension drawing of the water block above and the backplate below, with side views

Bykski drawing in millimeters. Water block above, backplate below.

Which Version Do I Need?

Confirm the PCB against each block’s compatibility list, then check where the fittings will sit in your case.

Bykski N-GV5090DWF-XTHIS PAGE
Choose this version for an acrylic window, 5V ARGB, and tubing routed to ports at the short end of the block.
Choose the SR if you prefer a stainless steel faceplate and POM construction.
Choose the X-V3 if your tubing route works better with the terminal centered along the top edge.

What's in the Box

1 × full-cover GPU water block with 5V ARGB lighting1 × aluminum backplate2 × G1/4 stop plugsThermal pad setMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Shut down and unplug the PC. Remove the graphics card and take off the stock cooler.
2
Clean off the old thermal materials. Compare the PCB and mounting holes with Bykski’s diagram.
3
Place the included thermal pads on the memory and power-delivery components shown in the installation diagram for this model. Apply your own thermal paste to the GPU die.
4
Align the water block, PCB, and backplate, then tighten the mounting screws evenly. If the holes do not line up, stop and recheck the PCB.
5
Connect your tubing with G1/4 fittings and seal the unused openings with the port plugs. Leak-test the loop with the graphics card unpowered.

You also need a pump, reservoir, radiator, coolant, tubing, and G1/4 fittings sized for your tubing.

Bykski N-GV5090DWF-X exploded installation drawing showing the block, pad strips, PCB, backplate, and screws in order

1. Water block · 2. Thermal pads · 3. Your graphics card PCB · 4. Backplate · 5. Backplate screws

FAQ

Does this block fit the Gigabyte RTX 5090 Gaming OC?

Yes. Bykski lists both the RTX 5090 GAMING OC 32G and RTX 5090 D GAMING OC 32G. Check the card model number and PCB against the compatibility section.

Is the included backplate water-cooled?

It is a passive aluminum backplate that mounts behind the PCB, outside the coolant path.

Which fittings does the block take?

Use G1/4 fittings that match your tubing. The inlet and outlet are at the short end of the block.

How do I connect the lighting?

Use a compatible 5V 3-pin ARGB header or controller. A 12V 4-pin RGB header can damage the lighting.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.

FormulaMod Official Store

Recent Reviews
+