• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

ASUS Prime RTX 5070 12GB Water Block with Backplate | Bykski N-AS5070PM-X

stars, based on ( 0 ) review
€133.25 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-AS5070PM-X

Full-cover water block for ASUS Prime RTX 5070 12GB

The Bykski N-AS5070PM-X is a full-cover water block for supported ASUS Prime GeForce RTX 5070 12GB GDDR7 boards. It replaces the stock cooler and transfers heat from the GPU core, memory, and voltage regulators to a custom liquid cooling loop. The included aluminum backplate mounts behind the PCB.

Fits
ASUS Prime RTX 5070 12GB
Cold plate
Copper
Port thread
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists these ASUS Prime PCB layouts for this block.

  • ✓ASUS Prime GeForce RTX 5070 12GB GDDR7 (PRIME-RTX5070-12G)
  • ✓ASUS Prime GeForce RTX 5070 12GB GDDR7 OC Edition (PRIME-RTX5070-O12G)

Not compatible:

  • ✗ASUS Prime GeForce RTX 5070 Ti 16GB

Before ordering, check your exact card model and compare its PCB outline, mounting holes, and component layout with Bykski’s drawing.

Bykski N-AS5070PM-X fit reference with the ASUS PRIME-RTX5070-12G stock cooler above Bykski’s drawing of the bare PCB

ASUS product image of the PRIME-RTX5070-12G above Bykski’s PCB layout drawing.

Design Highlights

Bykski N-AS5070PM-X underside with the copper cold plate and raised contact surfaces

A cold plate for the core, memory, and VRM

The raised areas of the cold plate meet the components they cool. Thermal pads bridge the contact surfaces on the memory and voltage regulators.

Bykski N-AS5070PM-X close-up of the 0.3 mm microchannels in the copper cold plate

0.3 mm coolant channels

Coolant passes through fine channels machined into the copper cold plate beneath the clear acrylic top.

Bykski N-AS5070PM-X black aluminum backplate showing mounting holes and a corner cutout

Black aluminum backplate

The backplate mounts on the rear of the card. Coolant stays in the block.

Key Specifications

ModelN-AS5070PM-X
Cold plateCopper
Copper cold plate length137.4 mm
TopClear acrylic
BackplateBlack aluminum
Port threadG1/4 inlet and outlet
Lighting5V 3-pin addressable RGB (RBW)
Block (L × W × T)191.06 × 151.58 × 26.15 mm
Backplate (L × W × T)191.06 × 121.53 × 6.11 mm
Bykski N-AS5070PM-X front and side dimension drawings of the water block and backplate

Bykski dimension drawing in millimeters. Block above, backplate below.

Which Version Do I Need?

Use the full card model on the label to choose a block.

Bykski N-AS5070PM-XTHIS PAGE
Choose this block for either of the listed ASUS Prime RTX 5070 12GB PCBs.
For ASUS Prime RTX 5070 Ti 16GB or Prime RTX 5080 16GB OC, see this bundle with a lighting controller and verify your PCB before ordering.
Choose this model for the ASUS TUF Gaming GeForce RTX 5070 Ti BTF White OC Edition.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2× G1/4 stop plugsThermal padsMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski N-AS5070PM-X exploded drawing of the block, pad strips, graphics card PCB, washers, screws, and backplate

Bykski assembly drawing. ① Water block · ② Thermal pads · ③ Your card’s PCB · ④ Washers · ⑤ Spring screws · ⑥ Backplate · ⑦ Backplate screws.

Installation & Use

1
Shut down the PC, remove the card, and take off its stock cooler. Clean off the old thermal pads and paste.
2
Use the drawing to identify the memory and MOSFET contact areas, then trim the thermal pads to fit. Apply your own thermal paste to the GPU die at 3.
3
Align the block, PCB, and backplate with the mounting holes. Place the washers as shown in the assembly drawing above and tighten the spring screws and backplate screws evenly.
4
Connect the block with G1/4 fittings and seal any unused ports with suitable port plugs. For lighting, use a compatible 5V 3-pin ARGB connection.
5
Leak-test the assembled loop before powering the graphics card.

You also need a pump, radiator, G1/4 fittings, tubing, and coolant.

Bykski N-AS5070PM-X PCB diagram with arrows pointing to the memory, MOSFETs, and GPU die

Bykski installation drawing. 1 memory pads · 2 MOSFET pads · 3 thermal paste on the GPU die.

FAQ

Does this fit the ASUS Prime RTX 5070 Ti?

The Prime RTX 5070 Ti 16GB uses a different block. Check the comparison above for its part number.

Does this block come with a backplate?

Yes. One black aluminum backplate is included, and coolant runs through the front block.

What fittings should I use?

Use G1/4 fittings and match them to your tubing.

Which RGB header should I use?

Use a compatible 5V 3-pin ARGB connection. A 12V RGB header can damage the LEDs.

Can this replace the stock cooler on its own?

It replaces the stock cooler as part of a custom loop. You will also need a pump, radiator, fittings, tubing, and coolant.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.

FormulaMod Official Store

Recent Reviews
+