• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Iluvatar CoreX TianGai 150 (BI-V150) GPU Water Block with Backplate | Bykski IC-BIV150-SR

stars, based on ( 0 ) review
€198.05 piece
items available
Contact Us
FormulaMod Official Store
Bykski · IC-BIV150-SR

Full-cover water block for TianGai 150

The Bykski IC-BIV150-SR is a full-cover GPU water block for the Iluvatar CoreX TianGai 150 (BI-V150) 64GB PCIe accelerator. It replaces the factory passive heatsink and transfers heat from the card to coolant in a custom loop. The all-metal block comes with a separate aluminum backplate and connects through G1/4 ports.

Fits
TianGai 150 (BI-V150)
Cold plate
Nickel-plated T2 copper
Ports
G1/4 female threads
Backplate
Aluminum, included

Compatibility

Bykski lists the BIV150 board layout shown here.

  • ✓Iluvatar CoreX TianGai 150 (BI-V150), 64GB HBM2e PCIe

Before ordering, compare your card’s PCB, mounting holes, and component layout with the reference photo.

Bykski IC-BIV150-SR compatibility reference showing the bare BIV150 PCB and its PCIe edge connector

Bykski’s reference photo of the BIV150 PCB.

Design Highlights

Bykski IC-BIV150-SR copper cold plate showing the internal coolant path and microchannel sections

Bykski’s cold plate illustration.

Coolant through the copper cold plate

Coolant passes through 0.3 mm jet microchannels in the nickel-plated copper cold plate before carrying heat away to your loop’s radiator.

Bykski IC-BIV150-SR flat aluminum backplate with its mounting holes

Separate aluminum backplate

The aluminum backplate screws onto the rear of the PCB. It mounts opposite the water block, with the card between the two parts.

Key Specifications

ModelBykski IC-BIV150-SR
Block materialsCopper and 304 stainless steel
Cold plateNickel-plated T2 copper
Copper plate length222.18 mm
BackplateAluminum
Port threadsG1/4 female
Block dimensions278.19 × 106.68 × 16.60 mm
Backplate dimensions266.63 × 106.70 × 4.00 mm
Net weight1.4 kg
Maximum working pressure4 bar
Working temperature−20 to 60 °C
Seal materialEPDM
Bykski IC-BIV150-SR dimension drawing with the block above and backplate below

The block is shown above the backplate. Dimensions are in millimeters.

Which Version Do I Need?

Choose based on how you want to set up liquid cooling for your TianGai 150.

Bykski IC-BIV150-SRTHIS PAGE
Choose this block and backplate if you’re building a custom loop or adding the card to one you already have.
Choose the all-in-one kit if you want the block, pump, tubing, and fan-equipped radiator in one assembly.

What's in the Box

1 × IC-BIV150-SR water block1 × aluminum backplate2 × 1.5 mm thermal pad strips8 × 0.5 mm insulating washers8 × M2 × 5 mm spring screws6 × backplate screws

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Remove the factory heatsink and clean the old thermal material from the card.
2
Fit the 1.5 mm pads to the MOSFET locations shown. Apply a thin layer of your own GPU thermal paste to the marked chip contact surfaces.
3
Align the block with the PCB holes and position the backplate on the rear. Fit the insulating washers and spring screws at the matching holes, then secure the backplate with its own screws. Tighten evenly and stop if the block does not sit flush.
4
Connect the block to the loop with G1/4 fittings and fill the reservoir. Power only the pump to circulate coolant, bleed air, and check for leaks. Keep the GPU and the rest of the system powered off during the test.

You’ll also need a pump, reservoir, radiator with fans, G1/4 fittings, matching tubing, and coolant compatible with your loop.

Bykski IC-BIV150-SR installation drawing showing the thermal pad strips and chip contact surfaces

The dark strips mark the thermal pad locations. The syringe symbols mark where to apply paste.

FAQ

How is the BI-V150 cooled from the factory?

Its original heatsink is passive and relies on airflow from the server’s chassis fans. Iluvatar rates the card at 350 W of board power.

Do I need a separate pump and radiator?

Yes. The IC-BIV150-SR connects to a custom loop, so you’ll need a pump and a radiator with fans.

What thermal pad thickness should I use?

Bykski specifies 1.5 mm pads for the MOSFET positions in the installation diagram.

How do I check clearance in my case?

The original BI-V150 is a full-length, full-height, dual-slot PCIe card. Use the block and backplate dimensions above to check clearances, allowing space for the fittings, tubing, and radiator.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.

FormulaMod Official Store

Recent Reviews
+