• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

XFX RX 6900 XT / 6800 XT Water Block for Select MERC 319 PCBs, Bykski A-XF6900XT-X

stars, based on ( 1 ) reviews
€133.25 piece
items available
Contact Us
FormulaMod Official Store
Bykski · A-XF6900XT-X

Full-cover water block for XFX MERC 319

The Bykski A-XF6900XT-X replaces the stock cooler on the XFX Radeon RX 6900 XT Speedster MERC 319 Ultra. Its copper cold plate cools the GPU core, memory, and voltage regulators in a custom liquid cooling loop. The block connects through G1/4 ports and comes with an aluminum backplate and 5V addressable lighting.

Fits
Select XFX MERC 319 PCBs
Coverage
GPU, memory, and VRM
Ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Confirmed card and PCB combinations

  • ✓XFX Radeon RX 6900 XT Speedster MERC 319 Ultra (RX-69XTACUD9)
  • ✓XFX Radeon RX 6800 XT Speedster MERC 319 (V1 PCB only)

Not compatible:

  • ✗XFX Radeon RX 6800 XT Overseas Edition (V2 PCB)

Before ordering, confirm your exact card model and compare the full PCB layout, component locations, and mounting holes.

Bykski A-XF6900XT-X PCB layout drawing showing component positions and mounting holes

Bykski’s PCB layout drawing for this block.

Design Highlights

Bykski A-XF6900XT-X angled front view showing the clear acrylic top and G1/4 terminal

Clear acrylic top

The clear top shows the coolant path and the copper cold plate beneath it.

Bykski A-XF6900XT-X close-up of the jet microchannel fins on the copper cold plate

Jet microchannels over the GPU core

Coolant passes through a bank of fine channels where the copper plate contacts the GPU core.

Bykski A-XF6900XT-X acrylic water block illuminated in pink, purple, and blue

Manufacturer’s lighting illustration.

5V addressable lighting

Connect the light strip to your motherboard with a matching 5V 3-pin ARGB adapter cable, or use a compatible 5V RBW controller. A 12V 4-pin RGB header will damage the strip.

Key Specifications

ModelBykski A-XF6900XT-X
Cold plateHigh-purity copper
TopClear acrylic
BackplateBlack aluminum, outside the coolant path
Backplate dimensions (L × H × T)266.49 × 117.48 × 6 mm (manufacturer’s drawing)
Port threadG1/4 inlet and outlet
Lighting5V 3-pin addressable RGB (RBW)
Bykski A-XF6900XT-X backplate front and side dimension drawing

Backplate dimensions in millimeters.

Which Version Do I Need?

Check the PCB revision before choosing a block for an XFX RX 6800-series card.

Bykski A-XF6900XT-XTHIS PAGE
Choose this block for the RX 6800 XT Speedster MERC 319 V1 PCB or the RX 6900 XT Speedster MERC 319 Ultra.
Choose this block for an XFX RX 6800 Overseas Edition or an XFX RX 6800 XT Overseas Edition V2 with the matching PCB.

What's in the Box

1 × full-cover water block1 × backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set1 × 5V ARGB light strip

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski A-XF6900XT-X exploded assembly drawing with water block, thermal pads, graphics card PCB, and backplate

Assembly reference. 1 Water block · 2 Thermal pads · 3 Your graphics card PCB · 4 Insulating washers · 5 Spring screws · 6 Backplate · 7 Backplate screws

Installation & Use

1
Power off the system and remove the graphics card. Take off the stock cooler and clean away the old thermal paste and pad residue.
2
Use the diagram to locate the memory and power delivery contact points for the thermal pads. Fit the pads there and apply a thin layer of your own thermal paste to the GPU die.
3
Align the block, PCB, and included backplate. Place the insulating washers over the matching screw holes on the back of the PCB. Tighten the spring screws gradually in a cross pattern, then fasten the remaining backplate screws.
4
Connect the block to your loop with G1/4 fittings and seal the unused ports with the stop plugs.
5
Fill the loop and run the pump alone to check for leaks before powering the graphics card.

You’ll need a pump, reservoir, radiator, tubing, matching G1/4 fittings, coolant, and your own thermal paste.

Bykski A-XF6900XT-X PCB diagram with shaded thermal pad locations and a paste applicator pointing to the GPU die

The shaded areas around the GPU show the pad positions on the memory and power delivery contacts. The applicator points to the GPU die, where thermal paste goes.

FAQ

Does this fit the XFX RX 6800 XT Speedster MERC 319?

It fits the V1 PCB. For the V2 PCB, compare your board with the A-XF6800-X listing.

Are thermal pads included?

The package includes one set of thermal pads. Apply them to the specified memory and power delivery contact points.

Is there an English installation manual?

The product does not come with English instructions. See the diagrams and mounting steps above.

What fittings does the block use?

Use G1/4 fittings for the inlet and outlet. Choose fittings that match the tubing in your loop.

Which header powers the lighting?

Use a matching 5V 3-pin ARGB adapter cable for a motherboard connection or use a compatible 5V RBW controller. A 12V 4-pin RGB header will damage the LEDs.

Notes
  • This is a repair or replace only item. Returns not accepted on compatibility issues or block has had water/fluid run through it.
  • Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item. Product does NOT come with English instructions.
  • Not responsible for any damage caused by or when using this product. Please use at your own risk.
Recent Reviews ( 1 )
By
Steven
Thursday, 07 October 2021
Pros:* Cheap, but still good quality* Does a good job with the cooling* RGB looks nice* Comes with free RGB controllerCons:* Does not cool the chokes (no coil while noticed because of this)* No instructions, so if it is your first time watercooling a gpu it might be a bit scary. Still straight forward* Rough machining (doesn't look like it affect performanceTemps with stock cooling:Core: 75-80CHotspot: 90-100CEdge Hotspot delta at load: -17CBoost clock: 2510Temps with Bykski block (PE360 with NF12 @ 900rmp and i9 10850k in same loop)Core: 50-55CHotspot: 65-72CEdge Hotspot delta at load: - 17CBoost clock: 2470
+