• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

ASUS PRIME RTX 5080 GPU Water Block with Backplate & ARGB Controller | Bykski N-AS5080PM-X

stars, based on ( 0 ) review
items available
Contact Us
FormulaMod Official Store
Bykski · N-AS5080PM-X

Full-cover water block for ASUS PRIME RTX 5080 and RTX 5070 Ti

The Bykski N-AS5080PM-X replaces the stock cooler on supported ASUS PRIME GeForce RTX 5080 and RTX 5070 Ti 16GB cards. Its T2 copper cold plate transfers heat from the GPU core, memory, and voltage regulators to a custom liquid cooling loop. The bundle includes a backplate and a 5V ARGB controller.

Fits
Listed ASUS PRIME RTX 5080 and 5070 Ti cards
Cold plate
T2 copper
Ports
G1/4 end ports
Lighting
5V 3-pin ARGB

Compatibility

Fits the following ASUS PRIME 16GB GDDR7 cards

  • ✓ASUS PRIME GeForce RTX 5080 OC Edition (PRIME-RTX5080-O16G)
  • ✓ASUS PRIME GeForce RTX 5080 (PRIME-RTX5080-16G)
  • ✓ASUS PRIME GeForce RTX 5070 Ti OC Edition (PRIME-RTX5070TI-O16G)
  • ✓ASUS PRIME GeForce RTX 5070 Ti (PRIME-RTX5070TI-16G)

Not compatible:

  • ✗ASUS TUF Gaming GeForce RTX 5080 16GB and OC Edition
  • ✗NVIDIA GeForce RTX 5080 Founders Edition

Before ordering, check your exact card model and verify the PCB layout and mounting holes for your card.

Bykski N-AS5080PM-X fitment photo of the bare ASUS PRIME GeForce RTX 5080 OC board, showing the GPU die and mounting holes

Bykski’s PCB photo for the ASUS PRIME GeForce RTX 5080 OC (PRIME-RTX5080-O16G).

Design Highlights

Bykski N-AS5080PM-X underside showing the GPU die contact area, raised contact surfaces, and clear end terminal

One cold plate for the core, memory, and VRM

The cold plate has separate contact surfaces for the GPU die, memory, and power delivery components. The included aluminum backplate mounts behind the PCB and stays outside the coolant path.

Bykski N-AS5080PM-X cold plate microchannel detail with the original 0.3 mm label

0.3 mm jet microchannels

The end terminal routes coolant through the cold plate. A bank of up to 56 narrow channels carries it across the area over the GPU die.

Bykski N-AS5080PM-X black-covered water block with purple and blue lighting visible through the window and end terminal

5V addressable RGB

The included lighting controller lets you run the block’s ARGB without motherboard lighting sync. For motherboard sync, use a compatible 5V 3-pin ARGB header. Keep the lighting off 12V 4-pin RGB headers.

Key Specifications

ModelN-AS5080PM-X
Cold plateT2 copper
TopPMMA acrylic
BackplateBlack aluminum backplate, passive
Coolant portsG1/4, at the end of the block
Microchannels0.3 mm jet microchannels, up to 56 channels (Bykski specification)
Microchannel surface area15,643.356 mm²
Water block (L × W × T)243.07 × 125.51 × 33.65 mm
Backplate envelope (L × W × T)243.07 × 125.51 × 26.32 mm
Lighting5V 3-pin addressable RGB (RBW)
Bykski N-AS5080PM-X dimension drawing with top and end views of the water block and backplate

Water block above, backplate below. The side views show the overall profiles in millimeters.

Which Version Do I Need?

Check the graphics card model first. If your card is an ASUS PRIME, check where you have space for the fittings before choosing between the two PRIME blocks.

Bykski N-AS5080PM-XTHIS PAGE
Choose this bundle for one of the listed PRIME cards when your tubing will connect at the short end of the block.
Choose this separate block for an ASUS TUF Gaming RTX 5080. Check the card models listed on its page.
Compare this version if you want the terminal near the middle of the long edge. Check the card models on its page.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate1 × 5V ARGB lighting controller2 × G1/4 stop plugsThermal pad setMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the system, remove the graphics card, and take off its stock cooler. Clean the old paste and pad residue from the card.
2
Place the supplied thermal pads on the memory and VRM contact areas shown in the mounting diagram. Apply your own thermal paste to the GPU die.
3
Align the water block with the PCB mounting holes. Fit the backplate, gaskets, and screws as shown in the mounting diagram. Stop if the mounting holes do not line up.
4
Connect the tubing with G1/4 fittings and seal the unused ports with the stop plugs.
5
Leak-test the loop with the graphics card still unpowered.

For a new loop, you also need a pump, reservoir, radiator, tubing with matching G1/4 fittings, and coolant.

Bykski N-AS5080PM-X exploded mounting diagram showing the block, pads, graphics card PCB, gaskets, screws, and backplate

1 block · 2 thermal pads · 3 your graphics card PCB · 4 gaskets · 5 spring screws · 6 backplate · 7 backplate screws.

FAQ

Does this fit the ASUS PRIME RTX 5080 OC?

Yes. Check for PRIME-RTX5080-O16G on your card and compare the PCB layout to the photo above.

Can I use it with an ASUS PRIME RTX 5070 Ti?

Yes. The compatibility list includes the ASUS PRIME RTX 5070 Ti 16GB and its OC Edition. Look for PRIME-RTX5070TI-16G or PRIME-RTX5070TI-O16G.

What fittings should I use?

Use G1/4 loop fittings sized for your tubing. Seal the unused ports with the included stop plugs.

Is the included backplate actively water-cooled?

The included aluminum backplate is passive. Coolant flows through the block on the front of the graphics card.

Can I run the lighting without motherboard sync?

Yes. The bundle includes a 5V ARGB controller for that setup. Use 5V 3-pin ARGB equipment for the lighting.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.

FormulaMod Official Store

Recent Reviews
+