Bykski
Sapphire RX 7900 XTX NITRO+ GPU Water Block, Bykski A-SP7900XTX-X
Full-cover GPU water block for Sapphire Radeon RX 7900 XTX NITRO+ and select PULSE cards
The Bykski A-SP7900XTX-X is a full-cover water block for the Sapphire Radeon RX 7900 XTX NITRO+ Vapor-X and the specific PULSE boards listed below. It replaces the stock cooler and uses a copper cold plate to transfer heat from the GPU, memory, and power stages to a custom liquid cooling loop.
Compatibility
Bykski lists these Sapphire Radeon PCB layouts.
- ✓Sapphire Radeon RX 7900 XTX NITRO+ Vapor-X 24GB (11322-01-40G)
- ✓Sapphire Radeon RX 7900 XTX PULSE 24GB (11322-02-20G)
- ✓Sapphire Radeon RX 7900 XT PULSE 20GB (11323-02-20G)
- ✓Sapphire Radeon RX 7900 XT PULSE Platinum OC 20GB (SKU prefix 11323-04)
Before ordering, check the exact model on your card label. Confirm that the mounting holes and component contact points on that model’s PCB match the block.
Design Highlights
Cooling across the GPU, memory, and VRM
The copper cold plate takes heat from the GPU die, memory modules, and voltage regulators. Coolant passes through the jet microchannels and carries the heat into the loop.
Aluminum backplate
The included backplate mounts behind the PCB and supports the board. Coolant runs through the block on the front of the card.
5V addressable lighting
The clear acrylic top shows the coolant channels and the light from the included ARGB strip. For motherboard sync, use a matching 5V ARGB adapter cable to connect the strip to a 5V 3-pin ARGB header. You can also use a compatible 5V ARGB controller.
Key Specifications
| Model | A-SP7900XTX-X |
|---|---|
| Cold plate | T2 copper |
| Top | Clear acrylic |
| Backplate | Black aluminum |
| Inlet and outlet thread | G1/4 |
| Block (L × W × T) | 276.70 × 147.82 × 23.05 mm |
| Backplate (L × W × T) | 276.70 × 117.15 × 6.00 mm |
| Lighting | 5V addressable RGB (RBW) |
Which Version Do I Need?
Match the block to the exact graphics card and PCB you own.
What's in the Box
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
You also need a pump, radiator, reservoir, G1/4 fittings, tubing, and coolant.
FAQ
Does this water block fit the Sapphire RX 7900 XTX PULSE?
Bykski lists the Sapphire Radeon RX 7900 XTX PULSE 24GB (11322-02-20G). Confirm that the mounting holes and component contact points on your card’s PCB match the block.
Which Sapphire RX 7900 XT PULSE boards fit?
Bykski lists the RX 7900 XT PULSE 20GB and the RX 7900 XT PULSE Platinum OC 20GB. Check your card’s model label and PCB layout.
Is this a complete water cooling kit?
This is a GPU block and backplate for a custom loop. You need a pump, radiator, reservoir, fittings, tubing, and coolant.
Which fittings do I need?
Use G1/4 fittings for the inlet and outlet, then close the unused ports with the supplied stop plugs.
How do I connect the 5V ARGB lighting?
Use a matching 5V ARGB adapter cable to connect the strip to a 5V 3-pin motherboard ARGB header, or use a compatible 5V ARGB controller. A 12V 4-pin RGB header will damage the strip.
- This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.












