• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Palit RTX 5090 GameRock 32GB Water Block – Bykski N-PT5090GK-X-V3

stars, based on ( 0 ) review
items available
Contact Us
FormulaMod Official Store
Bykski · N-PT5090GK-X-V3

Full-cover water block for Palit RTX 5090 GameRock

The Bykski N-PT5090GK-X-V3 replaces the stock cooler on the Palit GeForce RTX 5090 GameRock 32GB with the PCB layout shown below. Its nickel-plated copper cold plate transfers heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop. A separate aluminum backplate mounts behind the card.

Fits
Palit RTX 5090 GameRock 32GB
Cold plate
Nickel-plated copper
Ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

  • ✓Palit GeForce RTX 5090 GameRock 32GB

Before ordering, verify your exact card model and match its complete PCB layout to the bare board photo in Key Specifications.

Bykski N-PT5090GK-X-V3 fit reference showing the Palit GeForce RTX 5090 GameRock with its factory three-fan cooler

Palit GeForce RTX 5090 GameRock with its stock cooler.

Design Highlights

Bykski N-PT5090GK-X-V3 underside with the nickel-plated cold plate and raised contact surfaces

Cooling across the board

The cold plate has separate contact areas for the GPU die, the memory around it, and the power delivery components. Coolant carries their heat to the radiator in your loop.

Bykski N-PT5090GK-X-V3 front window and end terminal illuminated in purple and blue

A clear window into the coolant path

The acrylic window exposes the machined channels under the black faceplate. The block uses 5V addressable lighting.

Bykski N-PT5090GK-X-V3 black backplate with mounting holes and a notched edge

Separate aluminum backplate

The included backplate mounts behind the PCB. It stays outside the coolant path, so there is no rear section to plumb.

Key Specifications

ModelN-PT5090GK-X-V3
Cold plateNickel-plated copper
WindowClear acrylic
BackplateBlack anodized aluminum
Cooling coverageGPU core, memory, and voltage regulators
Inlet and outlet threadG1/4
Lighting5V 3-pin ARGB (RBW)
Bykski N-PT5090GK-X-V3 compatibility reference showing the bare Palit GameRock PCB, GPU die, and surrounding components

Bykski’s bare PCB reference. Compare the board outline, component positions, and mounting holes.

Which Version Do I Need?

Match your card to the PCB image for the version you choose. Then compare the port position with your planned tubing route.

Bykski N-PT5090GK-X-V3THIS PAGE
Choose this version for a black faceplate with a lit window and the port terminal at the short end.
Choose this version if you want a clear top and your tubing route suits a terminal near the middle of the long edge.
Choose this version if you prefer a stainless steel faceplate and POM construction.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplateThermal pads2× G1/4 stop plugsMounting hardware

The bundle with the additional lighting controller includes one controller.

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Shut down the PC, disconnect power, and remove the graphics card. Remove the stock cooler and clean off the old thermal material.
2
Check the PCB and mounting holes against Bykski’s reference. Place thermal pads on the specified memory and voltage regulator contact points and apply your own thermal paste to the GPU die.
3
Align the block, PCB, and backplate. Use the hardware and placement instructions for your kit, and tighten the screws gradually and evenly.
4
Connect the inlet and outlet to your loop with G1/4 fittings and seal unused ports. Leak-test the loop with the graphics card unpowered.

For a new loop, you also need a pump, reservoir, radiator, G1/4 fittings, matching tubing, and coolant.

Bykski N-PT5090GK-X-V3 installation reference showing the GameRock PCB, shaded pad positions, and thermal paste application on the GPU die

Bykski’s PCB diagram. Gray bars mark the pad positions. The applicator points to the GPU die.

FAQ

Will this fit my RTX 5090?

Check for the Palit GeForce RTX 5090 GameRock 32GB and match its PCB to Bykski’s bare board photo above.

Is the backplate included?

Yes. Both options include one black anodized aluminum backplate. It mounts on the back of the PCB and stays outside the coolant path.

Can I sync the lighting to my motherboard?

Use a compatible 5V 3-pin ARGB header. If you do not have one available, choose the bundle with the lighting controller. Keep the lighting lead off 12V 4-pin RGB headers.

What fittings do I need?

Use G1/4 fittings on the block and match the fittings to your tubing size.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.

FormulaMod Official Store

Recent Reviews
+