• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

MSI GeForce RTX 5090 D Gaming Trio OC GPU Water Block with Backplate – Bykski N-MS5090DTRIO-X

stars, based on ( 0 ) review
$215.17 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-MS5090DTRIO-X

Full-cover GPU water block for MSI RTX 5090 D Gaming Trio OC

The Bykski N-MS5090DTRIO-X is a full-cover water block for custom liquid cooling on select MSI graphics cards, including the MSI GeForce RTX 5090 D 32G Gaming Trio OC. It replaces the card’s stock cooler and transfers heat from the GPU core, memory, and voltage regulators to your coolant. An aluminum backplate is included.

Fits
MSI RTX 5090 D 32G Gaming Trio OC
Cold plate
Copper
Backplate
Black aluminum
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists these MSI graphics cards for this block.

  • ✓MSI GeForce RTX 5090 D 32G Gaming Trio OC
  • ✓MSI GeForce RTX 5090 32G Suprim OC
  • ✓MSI GeForce RTX 5090 32G Vanguard SOC

Before ordering, verify your exact graphics card model. Compare its PCB layout and mounting holes with Bykski’s reference board photo.

Bykski N-MS5090DTRIO-X fitment reference showing the MSI GeForce RTX 5090 D 32G Gaming Trio OC with its stock three-fan cooler above the bare reference PCB

MSI’s RTX 5090 D 32G Gaming Trio OC with its stock cooler above. Bykski’s bare PCB reference below.

Design Highlights

Bykski N-MS5090DTRIO-X underside showing the cold plate contact surfaces and mounting posts

One cold plate for the core, memory, and power stages

A copper cold plate spans the GPU core, memory, and voltage regulators. The included aluminum backplate mounts behind the PCB and stays outside the coolant path.

Bykski N-MS5090DTRIO-X coolant flow illustration with colored channels and a terminal at the short end

Manufacturer’s coolant flow illustration.

Microchannels and end ports

Coolant passes through 0.3 mm microchannels in the cold plate. The inlet and outlet are at the short end of the block. Check clearance there when planning your tube route.

Bykski N-MS5090DTRIO-X GPU water block illuminated violet and blue through its clear acrylic window

Addressable lighting through the acrylic window

The clear acrylic window shows the coolant channels. The block uses 5V 3-pin addressable RGB lighting, also called RBW.

Key Specifications

Model (SKU)N-MS5090DTRIO-X
Cooling coverageGPU core, memory, and voltage regulators
Cold plateCopper
Cold plate length158.30 mm
WindowClear acrylic (PMMA)
BackplateBlack aluminum
Microchannel width0.3 mm
Port locationShort end of the block
Block (L × W × T)243.23 × 137.74 × 33.30 mm
Backplate (L × W)243.22 × 137.75 mm
Lighting connector5V 3-pin ARGB (RBW)
Bykski N-MS5090DTRIO-X dimension drawing with top and side views of the water block and folded backplate

Manufacturer drawing in millimeters. Water block above and backplate below. The 25.90 mm dimension spans the folded edge.

Which Version Do I Need?

Match your exact graphics card first, then check the port location and available tubing clearance.

Bykski N-MS5090DTRIO-XTHIS PAGE
Choose this block for a card listed above when your tubing will connect at the short end.
Check your exact card model and PCB layout on the V2 listing before ordering. The terminal sits along the long edge, and the block measures 220.72 × 170.50 × 26.48 mm.
Use this listing if your card is the ASUS ROG Astral GeForce RTX 5090 32GB OC Edition.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplateThermal padsMounting hardware set2× G1/4 stop plugs

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Shut down and disconnect power. Remove the graphics card and its stock cooler, then clean off the old thermal material.
2
Cut the thermal pads to fit the memory and power stages shown in the diagram. Apply your own thermal paste to the GPU die.
3
Align the block and backplate with the PCB mounting holes and tighten the mounting screws evenly. If the holes do not line up, stop and check the PCB.
4
Connect the block to your custom loop and seal unused ports with the plugs. Power only the pump for the leak test and leave the rest of the system off.

You’ll also need a pump, radiator, coolant, tubing, and compatible fittings.

Bykski N-MS5090DTRIO-X installation diagram with shaded pad locations and a paste applicator pointing to the central GPU die

Bykski’s installation diagram. The gray areas mark where thermal pads go on the memory and power stages. Apply thermal paste to the GPU die at the center.

FAQ

Does this block fit the MSI RTX 5090 Vanguard SOC?

Yes. Bykski lists the MSI GeForce RTX 5090 32G Vanguard SOC. Verify the model and PCB layout before ordering.

Does the backplate carry coolant?

The included aluminum backplate mounts behind the graphics card. Coolant circulates through the main water block.

Which motherboard header should I use for the lighting?

For motherboard lighting control, use a 5V 3-pin ARGB header. Do not use a 12V 4-pin RGB header.

Where do the thermal pads go?

Use the gray areas in the installation diagram to locate the memory and power stages. Apply your own thermal paste to the GPU die.

How much room does the water block need?

The block measures 243.23 × 137.74 × 33.30 mm. Check clearance for the end ports, your fittings, and the tube route.

Notes
  • Verify your graphics card model and PCB layout before installing the block or running coolant through it. See FormulaMod’s Return Policy and Returns & RMA Policy for eligibility and instructions.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • If you notice a problem with the cold plate surface, take a photo and contact FormulaMod before installation.

FormulaMod Official Store

Recent Reviews
+