• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

RX 9070 XT Water Block for ASRock Taichi 16GB OC – Bykski A-AR9070XTTC-X

stars, based on ( 0 ) review
$146.41 piece
items available
Contact Us
FormulaMod Official Store
Bykski · A-AR9070XTTC-X

Full-cover water block for the ASRock RX 9070 XT Taichi

The Bykski A-AR9070XTTC-X replaces the stock cooler on the ASRock Radeon RX 9070 XT Taichi 16GB OC so you can connect the card to a custom liquid cooling loop. The copper cold plate cools the GPU core, memory, and power delivery components. The block includes an aluminum backplate and 5V addressable lighting.

Fits
ASRock Taichi 16GB OC
Cold plate
Copper
Loop ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

This block fits one ASRock PCB layout.

  • ✓ASRock AMD Radeon RX 9070 XT Taichi 16GB OC (RX9070XT TC 16GO)

Not compatible:

  • ✗ASRock AMD Radeon RX 9070 XT Challenger 16GB
  • ✗PowerColor Reaper Radeon RX 9070 XT

Before ordering, check the model on your card label and compare your PCB layout and mounting holes with Bykski’s bare-board photo.

Bykski A-AR9070XTTC-X compatibility photos showing the ASRock RX 9070 XT Taichi 16GB OC with its stock cooler above and the matching bare PCB with mounting holes below

ASRock’s stock card above and Bykski’s matching bare PCB below.

Design Highlights

Bykski A-AR9070XTTC-X underside illustration highlighting the copper cold plate and component contact surfaces

One cold plate covers the core, memory, and VRM

The shaped cold plate meets the GPU core and the pad locations for memory and power delivery. The separate aluminum backplate mounts behind the PCB.

Bykski A-AR9070XTTC-X close-up illustration of the jet microchannel fins in the copper cold plate

Bykski’s microchannel detail.

Coolant flows through 0.3 mm jet microchannels

The inlet directs coolant through the microchannel area over the GPU core. Match the inlet and outlet markings on the block when connecting your G1/4 fittings.

Bykski A-AR9070XTTC-X acrylic face illuminated in pink, purple, and blue

Clear acrylic with addressable lighting

The clear top shows the coolant channels. The RBW lighting uses a 5V 3-pin ARGB connection.

Key Specifications

Bykski modelA-AR9070XTTC-X
Cold plateCopper
TopClear acrylic
BackplateBlack aluminum, passive
Cooling coverageGPU core, memory, and VRM
Port threadsG1/4 inlet and outlet
Block (L × W × T)211.87 × 136.70 × 26.53 mm
Backplate (L × W × T)211.87 × 106.70 × 5.77 mm
Lighting5V 3-pin ARGB (RBW)
Bykski A-AR9070XTTC-X drawing with front and side dimensions for the water block and backplate

Bykski drawing in millimeters. Water block above, backplate below.

Which Version Do I Need?

Check the full card name on the label before choosing a block.

Bykski A-AR9070XTTC-XTHIS PAGE
Choose this Bykski block for the ASRock RX 9070 XT Taichi 16GB OC PCB listed above.
Compare Barrow’s separate full-cover block for the same ASRock Taichi 16GB OC card.
Choose this Bykski block for the PowerColor RX 9070 XT Reaper or Hellhound 16GB.
Choose this Bykski block for the GIGABYTE Radeon RX 9070 XT GAMING OC 16G.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs5V ARGB lighting stripThermal padsMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski A-AR9070XTTC-X clear water block shown alongside the included black aluminum backplate

Installation & Use

1
Power off the PC. Remove the graphics card, take off its stock cooler and backplate, and clean away the old thermal material.
2
Cut the supplied thermal pads to fit the memory and power delivery contacts shown in the diagram. Apply your own thermal paste to the GPU core.
3
Line up the block and PCB. Follow the mounting diagram to position the gaskets, the spring screws, and the backplate with its screws. Tighten gradually and evenly.
4
Connect the marked inlet and outlet to the loop with G1/4 fittings and close the unused openings with the supplied plugs. Connect the ARGB lighting to a matching 5V 3-pin connection if you want lighting.
5
Leak-test the loop before powering the graphics card.

For a new loop, you also need a pump, reservoir, radiator, coolant, and tubing with matching G1/4 fittings.

Bykski A-AR9070XTTC-X exploded mounting diagram showing the block, pads, customer GPU PCB, gaskets, screws, and backplate in order

1 Water block · 2 Thermal pads · 3 Your card’s PCB · 4 Gaskets · 5 Spring screws · 6 Backplate · 7 Backplate screws.

FAQ

Does this fit the ASRock RX 9070 XT Challenger?

Bykski lists the Taichi 16GB OC (RX9070XT TC 16GO) as the only supported card for this block.

Which block should I look for if I have a PowerColor RX 9070 XT Reaper?

Look for Bykski A-PC9070XT-X in the version guide. Match the full PowerColor card name before you order.

What fittings do I need?

Use G1/4 fittings sized for the tubing in your loop. Use the supplied plugs to seal unused openings.

Which header should I use for the lighting?

Use a compatible 5V 3-pin ARGB connection for the RBW lighting. A 12V 4-pin RGB header can damage the LEDs.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.

FormulaMod Official Store

Recent Reviews
+