Bykski
MSI RTX 3090/3080 Ti/3080 Gaming X Trio/Suprim X GPU Water Block, Active Backplate | Bykski N-MS3090TRIO-TC-V2
GPU water block with an active backplate for MSI Gaming X Trio and Suprim X
The Bykski N-MS3090TRIO-TC-V2 is a full-cover water block for select MSI GeForce RTX 3090, 3080 Ti, and 3080 Gaming X Trio and Suprim X graphics cards. The front block cools the GPU, memory, and voltage regulators. The included bridge routes coolant through the active backplate in the same custom loop to cool rear memory on supported RTX 3090 cards.
Compatibility
This water block fits only the six MSI GeForce PCB layouts below.
- ✓MSI GeForce RTX 3090 SUPRIM X 24G
- ✓MSI GeForce RTX 3090 GAMING X TRIO 24G
- ✓MSI GeForce RTX 3080 Ti SUPRIM X 12G
- ✓MSI GeForce RTX 3080 Ti GAMING X TRIO 12G
- ✓MSI GeForce RTX 3080 SUPRIM X 10G
- ✓MSI GeForce RTX 3080 GAMING X TRIO 10G
Before ordering, confirm the exact model and memory capacity, then compare your card’s PCB layout with Bykski’s compatibility information.
Design Highlights
Coolant flows through both sides
The front block and the active backplate each have a coolant channel. The backplate draws heat from the rear memory on supported RTX 3090 cards.
Jet microchannels over the GPU
The front cold plate uses jet microchannels with 0.3 mm spacing. The T2 copper plate also covers the front memory and power delivery contact areas.
One bridge connects both blocks
The bridge links the front block and active backplate in series. Bykski shows the inlet below the outlet. Follow the IN and OUT markings when you connect the tubing.
Key Specifications
| Model | N-MS3090TRIO-TC-V2 |
|---|---|
| Front cold plate | Nickel-plated T2 high-purity copper |
| Front cover | Clear acrylic |
| Active backplate | Plated copper cold plate with a clear acrylic cover |
| Port thread | G1/4 |
| Front block with terminal (L × W × T) | 278.32 × 157.88 × 44.55 mm |
| Active backplate (L × W × T) | 295.00 × 127.85 × 17.00 mm |
| Thermal pads in Bykski’s mounting diagram | 1.5 mm |
| Lighting | 5V 3-pin addressable RGB (Bykski RBW) |
Which Version Do I Need?
Start with the exact model on your card label, then choose the cooling layout you want.
What's in the Box
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
You also need a pump, reservoir, radiator and fans, G1/4 tubing fittings, matching tubing, coolant, and thermal paste.
FAQ
Does this fit the MSI RTX 3090 SUPRIM X 24G?
Yes. Bykski lists the MSI GeForce RTX 3090 SUPRIM X 24G. Verify the PCB layout before ordering.
Does coolant flow through the backplate?
Yes. The included bridge connects the front block to the active backplate so both share the same coolant loop.
What fittings do I need?
Use G1/4 fittings that match your tubing. Use the included stop plugs to seal unused ports.
Can I connect the lighting to a 12V RGB header?
Use a 5V 3-pin ARGB header or a compatible 5V ARGB controller. A 12V 4-pin RGB header can damage the LEDs.
- This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.














