Bykski
ASUS TUF RTX 3060 Ti Water Block (O8G) with Backplate | Bykski N-AS3070TITUF-X, fits ASUS TUF RTX 3070 Ti 8GB
Full-cover water block for ASUS TUF Gaming RTX 3060 Ti and RTX 3070 Ti
The Bykski N-AS3070TITUF-X replaces the stock cooler on compatible ASUS TUF Gaming cards. Its copper cold plate cools the GPU, memory, and voltage regulators. G1/4 ports connect the block to a custom liquid cooling loop, and the included aluminum backplate mounts behind the card.
Compatibility
Bykski lists these two ASUS TUF Gaming PCB layouts.
- ✓ASUS TUF Gaming RTX 3070 Ti 8GB (TUF-RTX3070TI-8G-GAMING)
- ✓ASUS TUF Gaming RTX 3060 Ti OC 8GB (TUF-RTX3060TI-O8G-GAMING)
Before ordering, check the full model code on your card and verify its PCB layout.
Design Highlights
One cold plate for the GPU, memory, and VRM
The full-cover plate picks up heat from the GPU die, memory modules, and voltage regulators. Coolant carries that heat into the loop.
0.3 mm jet microchannels
Coolant passes through narrow channels in the T2 copper plate. The clear acrylic top shows the flow path.
5V addressable lighting
The RBW light strip illuminates the clear top. Use a compatible 5V ARGB controller or connect to a 5V 3-pin motherboard header with a matching sync cable.
Key Specifications
| Model | N-AS3070TITUF-X |
|---|---|
| Cold plate | T2 copper |
| Top | Clear acrylic |
| Backplate | Black aluminum, outside the coolant path |
| Port thread | G1/4 |
| Microchannel gap | 0.3 mm |
| Block width | 147.55 mm, including the terminal |
| Backplate (L × W × T) | 239.85 × 117.55 × 6.00 mm |
| Lighting | 5V 3-pin ARGB (Bykski RBW) |
What's in the Box
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
For the loop, have G1/4 tubing fittings, matching tubing, a pump, a radiator, and coolant on hand.
FAQ
Which ASUS TUF RTX 3060 Ti does this block fit?
Bykski lists the TUF-RTX3060TI-O8G-GAMING. Verify the complete model code and PCB before ordering.
Which ASUS TUF RTX 3070 Ti does it fit?
Bykski lists the TUF-RTX3070TI-8G-GAMING. Check the PCB layout as well as the model code.
Which fittings do I need?
Use G1/4 tubing fittings that match your tubing. The two included G1/4 stop plugs seal the unused ports.
Can I connect the lighting to a 12V RGB header?
Connect to a 5V 3-pin ARGB header with a matching sync cable, or use a compatible 5V ARGB controller. A 12V RGB header can damage the light strip.
- This is a repair or replace only item. Returns not accepted on compatibility issues or if block has had water/fluid run through it.
- Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item. Product does NOT come with English instructions. Please see product gallery images for install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points with the exception of the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
- Not responsible for any damage caused by or when using this product. Please use at your own risk.














