• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Hygon DCU K100 AIO Liquid Cooler, 360 mm | Bykski B-FRD-HG-DCUK100-360

stars, based on ( 0 ) review
items available
Contact Us
FormulaMod Official Store
Bykski · B-FRD-HG-DCUK100-360

360 mm all-in-one liquid cooling for the Hygon DCU K100

The Bykski B-FRD-HG-DCUK100-360 is an all-in-one liquid cooler for a single Hygon DCU K100 with the PCIe board layout shown below. Its full-cover block replaces the stock cooler and draws heat from the chip, memory, and power stages. Connected tubing and an inline pump carry that heat to a 360 mm fan-cooled radiator.

Fits
Hygon DCU K100
Radiator
360 mm aluminum
Cooling
Full-cover block
Pump
Inline

Compatibility

Bykski lists this board layout

  • ✓Hygon DCU K100 (PCIe PCB shown)

Check your card's bare PCB against the photo before ordering.

Bykski B-FRD-HG-DCUK100-360 fit reference showing the bare Hygon DCU K100 PCB and its PCIe edge connector

Hygon DCU K100 bare board (manufacturer photo).

Design Highlights

Bykski B-FRD-HG-DCUK100-360 with the GPU block, three radiator fans, braided tubing, and inline pump

One loop for the card and radiator

Three 120 mm fans move air through the 360 mm radiator. Braided tubing connects the block and radiator, with the pump mounted in the tubing.

Bykski B-FRD-HG-DCUK100-360 underside showing the copper cold plate and raised component contact areas

Copper contact plate for the chip, memory, and power stages

The cold plate uses nickel-plated T2 copper. Bykski rates the copper itself at 401 W/(m·K). A 0.3 mm jet microchannel design directs coolant across the finned area over the chip.

Bykski B-FRD-HG-DCUK100-360 inline pump exploded view showing the cap, motor, impeller, and housing

Pump mounted between the block and radiator

The pump circulates coolant through the block and radiator. Bykski lists a rated speed of 7,000 RPM, a flow rate of 450 L/h, and a head of 7 m.

Key Specifications for the Single-Card Kit

ModelB-FRD-HG-DCUK100-360
Cold plateNickel-plated T2 copper
CoverageChip, memory, and power stages
Block dimensions253.47 × 95.93 × 18.03 mm
Cold plate design0.3 mm jet microchannels
Radiator360 mm aluminum with 12 coolant channels
Fans3 × 120 mm
PumpInline, 7,000 RPM, 450 L/h rated flow, 7 m head
TubingBraided and preconnected
Bykski B-FRD-HG-DCUK100-360 drawing showing the block length, width, and thickness

Manufacturer drawing. Block dimensions are in millimeters.

Which Version Do I Need?

Choose the configuration that matches the number of K100 cards you want to cool.

B-FRD-HG-DCUK100-360THIS PAGE
Choose the standard 360 mm kit for one matching Hygon DCU K100. The specifications and box contents apply to this option.
B-FRD-HG-DCUK100-360-H
For a two-card build, choose the thick-radiator option and confirm the radiator clearance in your case before ordering.

What's in the Box for the Single-Card Kit

1 AIO assembly with GPU block, 360 mm radiator, inline pump, and tubing3 × 120 mm fans1 backplate6 × 1.5 mm thermal pad strips4 × 0.5 mm washers4 × M2 × 5 mm spring screws8 backplate screws

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Bykski B-FRD-HG-DCUK100-360 exploded mounting diagram showing the GPU block, pads, PCB, and backplate

1 block · 2 pad strips · 3 your PCB · 4 washers · 5 spring screws · 6 backplate · 7 backplate screws

Installation & Use

1
Shut down and disconnect power. Remove the card's stock cooler and clean off the old thermal paste and pads.
2
Place 1.5 mm thermal pads on the memory and power stages shown in the installation diagram. Apply your own GPU thermal paste to the chip.
3
Align the block with the card's mounting holes. Fit the washers and spring screws, then attach the backplate with its screws. Stop if the mounting holes do not line up.
4
Mount the radiator and fans in a 360 mm position. The case top is one option if there is room for the radiator, fans, tubing, and inline pump.
5
Connect the pump and fans to matching power connectors on your system. Check the tubing connections for leaks and confirm the pump and fans are running before putting the card under load.

You also need your own GPU thermal paste, a 360 mm radiator mount with room for the fans and tubing, and matching power connections for the pump and fans.

Bykski B-FRD-HG-DCUK100-360 pad placement drawing showing shaded memory and power stages around the chip

Shaded areas take thermal pads. The syringe marks where to apply GPU thermal paste.

FAQ

Which Hygon K100 card does this cooler fit?

Bykski lists the Hygon DCU K100 with the PCIe board layout shown in the compatibility photo. Compare the bare PCB before ordering.

Do I need to buy a pump for the K100 AIO?

The inline pump comes connected between the water block and radiator as part of the single-card kit.

Will the single-card kit fit my case?

Look for a 360 mm radiator mount. Check the total depth available for the radiator and fans, and leave room to route the tubing to the card.

What does the -H option mean?

It identifies the 360 mm thick-radiator option for a two-card setup.

What thickness of thermal pads goes on the card?

Use the 1.5 mm strips on the memory and power stages shown in the installation diagram.

Notes
  • For any questions, please contact customer service.

FormulaMod Official Store

Recent Reviews
+