• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

NVIDIA Tesla T4 AIO Liquid Cooling Kit, Bykski B-FRD-TESLA-T4 360 mm

stars, based on ( 0 ) review
items available
Contact Us
FormulaMod Official Store
Bykski · B-FRD-TESLA-T4

360 mm AIO liquid cooler for the NVIDIA Tesla T4

The Bykski B-FRD-TESLA-T4 is a 360 mm all-in-one liquid cooler for the NVIDIA Tesla T4 16GB low-profile PCIe GPU. The stock T4 uses a passive heatsink that relies on chassis airflow. The Bykski kit replaces it with a full-cover water block and moves heat to a fan-cooled radiator in inference workstations with a 360 mm mount.

Fits
NVIDIA Tesla T4 16GB
Radiator size
360 mm
Cold plate
T2 copper
Cooling loop
Inline pump

Compatibility

  • ✓NVIDIA Tesla T4 16GB GDDR6, single-slot half-height, half-length PCIe GPU with the pictured NVIDIA PCB layout

Compare your card’s PCB layout and mounting holes with the photo before ordering.

Bykski B-FRD-TESLA-T4 fit reference showing the bare NVIDIA Tesla T4 PCB and mounting holes

Bykski PCB photo with markings masked for layout comparison.

Design Highlights

Bykski B-FRD-TESLA-T4 standard assembly with a three-fan radiator, inline pump, and GPU block

Full-cover GPU block with an inline pump

The T2 copper cold plate draws heat from the GPU core. Thermal pads transfer heat from the memory and power components into the same block.

The pump sits in the tubing between the GPU block and the radiator. The standard 360 mm kit pairs the radiator with three fans.

Bykski B-FRD-TESLA-T4 standard 360 mm radiator face with cooling fins and mounting holes

Aluminum radiator in the standard 360 mm kit

Bykski shows 12 coolant channels for the standard 360 mm kit. The fans move air across the radiator fins to carry heat out of the loop.

Key Specifications

ModelBykski B-FRD-TESLA-T4
360 mm optionsB-FRD-TESLA-T4-360 (standard)
B-FRD-TESLA-T4-360-H (dual T4)
Cold plateT2 copper with 0.3 mm jet microchannels
Radiator, standard kit360 mm aluminum, 12 coolant channels (Bykski design)
Radiator length396 mm (standard drawing)
Block dimensions201.41 × 100.92 × 16.5 mm (standard drawing)
Inline pump, standard kit7,000 RPM, rated flow 450 L/h, rated head 7 m
Bykski B-FRD-TESLA-T4 cold head diagram showing length, bracket height, and thickness

Bykski block drawing. The height includes the illustrated bracket.

Which Version Do I Need?

Choose the cooler that matches your card count and the type of loop you are building.

Bykski B-FRD-TESLA-T4 AIOTHIS PAGE
Choose the standard kit for one T4 or the thick-radiator kit for two T4s.
Standalone block for an NVIDIA Tesla T4 in a custom loop. Before ordering, compare your PCB layout and mounting holes with this block’s own compatibility diagram.
For a Leadtek Tesla T4 in a custom loop, compare your PCB with the board layout shown for this water block.

What’s in the Box · Standard 360 mm Kit

1 × AIO assembly with GPU block, inline pump, tubing, and radiator3 × radiator fans1 × backplate

For installation, have 1.5 mm thermal pads ready.

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Remove the card’s factory heatsink and clean off the old thermal material from the GPU die, memory, and power components.
2
Place the 1.5 mm thermal pads on the memory and power components that meet the block’s raised contact areas. Apply your own GPU thermal paste to the die.
3
Align the water block with the PCB screw holes and secure it with the correct mounting hardware. Mount the backplate.
4
Install the radiator and fans in the case. Route the attached tubing without kinks and connect the pump and fans to their specified power connections.
5
Check the tubing joints for leaks before powering the GPU. Verify pump and fan operation before running a workload.

Also needed for the standard kit: a case with a 360 mm radiator mount, matching power connections for the pump and fans, and your own GPU thermal paste.

Bykski B-FRD-TESLA-T4 installation illustration with a top-mounted radiator and tubing routed to the GPU

Bykski installation illustration showing a top-mounted radiator.

FAQ

What cooling type does the NVIDIA Tesla T4 use?

The stock 70 W Tesla T4 is passively cooled and depends on air moved through the chassis. This kit replaces the passive heatsink with a liquid cold plate, inline pump, and fan-cooled radiator.

Do I need to buy a separate pump?

The standard AIO includes an inline pump in the tubing between the water block and the radiator.

Will the radiator fit my case?

Look for a 360 mm radiator mount with room for the fans and tubing bends. The standard radiator drawing shows an overall length of 396 mm. Check clearance for the version you plan to install.

What is the -H option?

The -360-H option is the 360 mm thick-radiator configuration for a dual-T4 build. Choose the standard -360 for a single T4.

Notes
  • If the block does not line up with the PCB screw holes, stop and have a technician check the fit.

FormulaMod Official Store

Recent Reviews
+