• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

NVIDIA H200 NVL 141 GB PCIe AIO Cooling System, Bykski B-FRD-H200, 360 mm

stars, based on ( 0 ) review
items available
Contact Us
FormulaMod Official Store
Bykski · B-FRD-H200

360 mm liquid cooler for the NVIDIA H200 NVL

The Bykski B-FRD-H200 is a full-cover all-in-one liquid cooler for the NVIDIA H200 NVL 141 GB PCIe accelerator with the board layout shown below. The water block replaces the card’s stock passive heatsink. An inline pump moves coolant to a 360 mm radiator, where the radiator fans carry heat out of the loop.

Fits
NVIDIA H200 NVL 141 GB PCIe
Radiator
360 mm aluminum
Cold plate
T2 copper
Pump
Inline

Compatibility

Compatible board

  • ✓NVIDIA H200 NVL 141 GB PCIe with the PCB layout shown here

Bykski labels this board NVIDIA Tesla H200 141G in its compatibility drawing. NVIDIA uses 141 GB for both the PCIe NVL card and the H200 SXM module.

Before ordering, compare your card’s PCB with the manufacturer’s reference photo.

Bykski B-FRD-H200 compatibility photo of the bare NVIDIA H200 NVL board with PCIe edge fingers and a right-side power lead

H200 PCB (manufacturer photo)

Design Highlights

Bykski B-FRD-H200 standard assembly showing a three-fan radiator, inline pump and attached GPU water block

Move GPU heat to a case-mounted radiator

The H200 NVL’s stock heatsink relies on airflow provided by the system. This kit moves heat to a case-mounted radiator with three fans on the standard 360 mm assembly. The inline pump sits in the braided tubing between the radiator and the block.

Bykski B-FRD-H200 underside showing the GPU contact area and raised contact surfaces on the cold plate

Full-cover T2 copper cold plate

The cold plate contacts the GPU package and the surrounding components marked in the installation diagram. The 0.3 mm jet microchannels increase the area where coolant contacts the copper.

Key Specifications

ModelB-FRD-H200
Standard 360 mm modelB-FRD-H200-360
Cold plateT2 copper
Cold plate microchannels0.3 mm, up to 48 channels
Block dimensions266.63 × 98.25 × 16.75 mm
BackplateBlack
Radiator360 mm aluminum
Radiator fans3 on the standard 360 mm assembly
Pump and tubingInline pump with braided tubing
Thermal pads1.5 mm
Bykski B-FRD-H200 manufacturer drawing of the block front and side with length, width, and thickness

Water block dimensions (manufacturer drawing)

Which Version Do I Need?

Start with the board match, then choose a cooler for your case or existing loop.

Bykski B-FRD-H200THIS PAGE
Choose the all-in-one cooler if you need a pump and 360 mm radiator with the block and have room to mount the radiator.
Choose this block and backplate for a custom liquid-cooling loop. Ask us to confirm your exact PCB for the N-H200-SR-QH before ordering.
An Astralcooler all-in-one option for H200 141 GB with its own inline pump and radiator. Compare its PCB and mounting drawings with your build.
An Astralcooler block and backplate for a custom loop. Choose it if you already have a loop or plan to build one, after checking its PCB drawing.

What's in the Box

360 mm AIO assembly with 1 full-cover GPU water block, inline pump, radiator and fans1 × backplate5 × 1.5 mm thermal pad strips4 × washers4 × spring screws6 × M2 × 9.5 mm backplate screws

Package contents shown are for the standard single-card B-FRD-H200-360.

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Verify the PCB match and check the case for radiator, fan, and tubing clearance.
2
Shut down the system, remove the GPU and take off its stock heatsink. Clean away the old thermal material.
3
Cut the 1.5 mm pads to fit the contact points marked in the diagram. Apply thermal paste to the GPU die.
4
Align the water block with the PCB’s mounting holes and secure it and the backplate with the mounting hardware. Stop if the holes do not line up.
5
Mount the radiator and fans. Route the tubing without sharp bends. Match the pump and fan leads to the power connections specified for your kit.
6
Inspect the tubing and fittings for visible leaks before using the card.

You’ll also need a case with a 360 mm radiator mount and clearance for the radiator, fans, and tubing. Have GPU thermal paste and suitable pump and fan power connections ready.

Bykski B-FRD-H200 application drawing showing thermal pad positions around the GPU die and a thermal paste syringe at the center

Dark strips and squares mark thermal pad locations. Apply thermal paste to the GPU die at the center.

FAQ

How does the NVIDIA H200 NVL cooling system work?

The H200 NVL ships with a passive heatsink that relies on system airflow. The Bykski AIO replaces it with a water block and uses an inline pump to move heat to a fan-cooled 360 mm radiator.

Do I need to buy a separate pump?

The kit includes a pump in the tubing between the GPU block and the radiator.

How can I tell which 141 GB H200 I have?

Check the form factor. The H200 NVL is a PCIe card. The H200 SXM is a module for a different mount. Compare your PCIe board with the photo above.

Will the radiator fit in my case?

Look for a 360 mm radiator mount with room for the fans and the tubing route to the GPU. The manufacturer illustrates a top-mounted radiator in a tower case.

Notes
  • The PCB shown in the installation drawing identifies the card you supply.

FormulaMod Official Store

Recent Reviews
+