• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

RX 7900 XT Reference GPU Water Block with Backplate | Bykski A-RX7900XT-X

stars, based on ( 0 ) review
$146.41 piece
items available
Contact Us
FormulaMod Official Store
Bykski · A-RX7900XT-X

Full-cover water block for the Radeon RX 7900 XT reference PCB

The Bykski A-RX7900XT-X replaces the stock cooler on the AMD Radeon RX 7900 XT reference PCB. Its copper cold plate transfers heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop. The block has a clear acrylic top and comes with a black aluminum backplate.

Fits
AMD RX 7900 XT reference
Ports
G1/4
Lighting
5V 3-pin ARGB
Backplate
Black aluminum

Compatibility

Match your card to the AMD reference PCB layout.

  • ✓AMD Radeon RX 7900 XT 20GB (AMD reference PCB)

Not compatible:

  • ✗AMD Radeon RX 7900 XTX (reference PCB)
  • ✗Radeon RX 7900 XT with a non-reference PCB

Before ordering, check the full model name and compare the component layout and mounting holes with the PCB photo in the product gallery.

Bykski A-RX7900XT-X compatibility reference photo of the AMD Radeon RX 7900 XT card with its three-fan stock cooler

AMD Radeon RX 7900 XT reference card with its original cooler.

Design Highlights

Bykski A-RX7900XT-X underside illustration highlighting the copper cold plate and its raised contact surfaces

Full-cover copper cold plate

The cold plate picks up heat at the GPU core, memory, and voltage regulators. Coolant carries that heat to the radiator in your loop.

Bykski cold plate design illustration with microchannel fins in the center

Jet microchannels over the GPU core

Coolant passes through the fine channels in the cold plate above the GPU core.

Bykski A-RX7900XT-X clear acrylic top and port terminal lit in red, purple, and blue

Clear acrylic with 5V lighting

The clear top leaves the coolant channels visible. The included ARGB strip uses a 5V 3-pin connection.

Key Specifications

ModelA-RX7900XT-X
Cold plateT2 copper
TopClear acrylic
BackplateBlack aluminum
Cooling coverageGPU core, memory, and VRM
Inlet and outlet threadG1/4
Lighting connector5V 3-pin ARGB (Bykski RBW)
Water block (L × W × T)263.65 × 137.06 × 23.15 mm
Backplate (L × W × T)263.65 × 106.77 × 6.00 mm
Bykski A-RX7900XT-X dimension drawing of the water block above the backplate, with front and side views

Bykski dimension drawing in millimeters. Water block above, backplate below.

Which Version Do I Need?

Start with the full name on your graphics card. Each of these blocks has its own PCB fit list.

Bykski A-RX7900XT-XTHIS PAGE
Choose this block for the AMD Radeon RX 7900 XT reference PCB.
For ASUS TUF Gaming Radeon RX 7900 XT OC or RX 7900 XTX OC cards.
For the ASRock Radeon RX 7900 XTX Taichi 24GB OC.

What's in the Box

1 × GPU water block1 × aluminum backplate2 × G1/4 stop plugsThermal padsMounting hardware set1 × 5V ARGB strip1 × ARGB sync cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the PC. Remove the graphics card and its stock cooler, then clean away the old thermal materials.
2
Check that the block matches the PCB and its mounting holes. Cut the supplied pads to fit the marked memory and power delivery areas. Apply a thin layer of your own thermal paste to the GPU die.
3
Align the block, PCB, and backplate. Start the mounting screws by hand and tighten them gradually in a cross pattern. Secure the backplate with its screws.
4
Connect the loop with G1/4 fittings and close the unused ports with the stop plugs. For lighting, align the sync cable with the 5V mark on a 5V 3-pin ARGB header.
5
Leak-test the loop with the graphics card unpowered.

Your loop also needs a pump, radiator, G1/4 fittings, tubing, and coolant.

Bykski A-RX7900XT-X PCB diagram showing shaded memory and power delivery pad locations and the GPU die in the center

Bykski’s thermal material placement diagram. The shaded areas around the GPU die show where to place the pads.

FAQ

Will this block fit an RX 7900 XTX?

No. A-RX7900XT-X fits the AMD Radeon RX 7900 XT reference PCB. Check your exact XTX model for a matching block.

Will it fit a partner-brand RX 7900 XT?

Confirm that your card uses the AMD reference PCB. Compare the board layout and mounting holes with the photo in the product gallery before ordering.

Does it come with a backplate?

Yes. One black aluminum backplate is included.

Can I connect the lighting to a 12V RGB header?

Use a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the LED strip.

Which fittings do I need?

Use G1/4 fittings that match your tubing. Two G1/4 stop plugs are included for unused ports.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.

FormulaMod Official Store

Recent Reviews
+