Bykski
RX 6900 XT / RX 6800 XT Red Devil GPU Water Block, Bykski A-PC6900XT-X for PowerColor
GPU water block for PowerColor RX 6900 XT / 6800 XT
The Bykski A-PC6900XT-X replaces the stock cooler on supported PowerColor Radeon RX 6900 XT and RX 6800 XT cards. Its copper cold plate transfers heat from the GPU core, memory, and voltage regulators to a custom liquid cooling loop. The block includes an aluminum backplate and 5V addressable RGB lighting.
Compatibility
Match the exact PowerColor card and PCB layout.
- ✓PowerColor Radeon RX 6900 XT Red Devil (AXRX 6900 XT 16GBD6-3DHE/OC)
- ✓PowerColor Radeon RX 6800 XT Red Devil (AXRX 6800 XT 16GBD6-3DHE/OC)
- ✓PowerColor Radeon RX 6800 XT Red Dragon, matching PCB without the raised cylindrical capacitors in the outlined areas
Not compatible:
- ✗PowerColor Radeon RX 6800 XT Red Dragon PCB with raised cylindrical capacitors in the outlined areas
For Red Dragon, compare the capacitor locations in the photos. For Red Devil, see the RX 6900 XT layout reference below. Before ordering, verify the entire PCB on your exact card.
Design Highlights
Coolant path through the cold plate
Coolant flows through 0.5 mm jet microchannels above the GPU core. The cold plate also contacts the memory and voltage regulators through thermal pads.
Separate aluminum backplate
The included black backplate mounts behind the PCB and stays outside the coolant path. The front of the block has a clear acrylic cover.
PowerColor Red Devil PCB reference
Bykski’s drawing shows the RX 6900 XT layout. Compare the mounting holes and the component locations where the cold plate contacts your card.
Key Specifications
| Model | A-PC6900XT-X |
|---|---|
| Coverage | GPU core, memory, and voltage regulators |
| Cold plate | Copper |
| Cover | Clear acrylic |
| Backplate | Black aluminum |
| Port thread | G1/4 |
| Jet microchannels | 0.5 mm |
| Block (L × W × T) | 264.71 × 150.43 × 23.51 mm |
| Backplate (L × W × T) | 264.81 × 120.29 × 6 mm |
| Lighting | 5V 3-pin addressable RGB (RBW) |
Which Version Do I Need?
Match your board to the listing for your exact card.
What's in the Box
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
Connect the block to a custom loop with G1/4 fittings, matching tubing, coolant, a pump, and a radiator. A reservoir is commonly used for filling and bleeding.
FAQ
How can I tell if my RX 6800 XT Red Dragon fits?
Match the entire PCB to the upper photo. The compatible board has no raised cylindrical capacitors in the outlined areas.
How does Liquid Devil differ from Red Devil?
PowerColor’s RX 6800 XT and RX 6900 XT Liquid Devil cards come with a factory-installed water block. Use the compatibility list above to match your exact card.
What fittings go on this block?
Use G1/4 loop fittings. Follow the inlet and outlet marks on the block and seal the unused openings with the two included stop plugs.
How do I connect the ARGB strip?
Use a compatible 5V ARGB adapter cable for the motherboard’s 5V 3-pin ARGB header, or connect the strip to a 5V controller compatible with Bykski RBW. A 12V 4-pin RGB header can damage the strip.
- This is a repair or replace only item. Returns not accepted on compatibility issues or if block has had water/fluid run through it.
- Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item.
- Not responsible for any damage caused by or when using this product. Please use at your own risk.













