• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

GIGABYTE RX 9070 XT GAMING OC 16G Water Block with Backplate | Bykski A-GV9070GMOC-X

stars, based on ( 0 ) review
€133.25 piece
items available
Contact Us
FormulaMod Official Store
Bykski · A-GV9070GMOC-X

Full-cover water block for GIGABYTE RX 9070 XT GAMING OC

The Bykski A-GV9070GMOC-X replaces the stock cooler on supported GIGABYTE cards such as the Radeon RX 9070 XT GAMING OC 16G. In a custom liquid cooling loop, its nickel-plated copper cold plate carries heat from the GPU, memory, and power stages to the coolant. The included aluminum backplate mounts behind the circuit board.

Fits
GIGABYTE GAMING OC 16G (RX 9070 XT / RX 9070)
Cold plate
Nickel-plated T2 copper
Port thread
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Match the full GIGABYTE card model and part number.

  • ✓GIGABYTE Radeon RX 9070 XT GAMING OC 16G (GV-R9070XTGAMING OC-16GD)
  • ✓GIGABYTE Radeon RX 9070 GAMING OC 16G (GV-R9070GAMING OC-16GD)

Before ordering, verify your card’s exact PCB layout and mounting holes. See the PCB drawing under Installation & Use for the RX 9070 XT GAMING OC layout.

Bykski A-GV9070GMOC-X compatibility photo showing the GIGABYTE RX 9070 XT GAMING OC graphics card with its stock cooler

GIGABYTE Radeon RX 9070 XT GAMING OC 16G with its stock cooler.

Design Highlights

Bykski A-GV9070GMOC-X angled view showing the microfin array, coolant channels, and inlet and outlet through the clear top

Coolant flow through the cold plate

Coolant flows through 0.3 mm jet microchannels in the copper cold plate. The clear acrylic top lets you see the channels.

Bykski A-GV9070GMOC-X water block shown alongside its black aluminum backplate

Separate aluminum backplate

The black anodized backplate mounts to the rear of the card and stays outside the coolant path.

Bykski A-GV9070GMOC-X clear water block illuminated in pink, violet, and blue

5V addressable RGB

Connect the lighting to a compatible 5V 3-pin ARGB header. Keep it off 12V 4-pin RGB headers.

Key Specifications

Model (SKU)A-GV9070GMOC-X
Cooling coverageGPU core, memory, and voltage regulators (VRM)
Cold plateNickel-plated T2 copper
TopClear acrylic
Microchannels0.3 mm jet-type
BackplateBlack anodized aluminum, passive
Port threadG1/4 inlet and outlet
Lighting5V 3-pin ARGB (RBW)
Water block (L × W × T)219.95 × 149.47 × 26.25 mm
Backplate (L × W × T)219.95 × 119.47 × 5.98 mm
Bykski A-GV9070GMOC-X dimension drawing showing plan and side views of the water block and backplate

Bykski dimension drawing. Water block above, backplate below. Measurements are in millimeters.

Which Version Do I Need?

Bykski A-GV9070GMOC-XTHIS PAGE
Choose this block for one of the GIGABYTE GAMING OC boards listed above after matching its PCB.
Check this separate block if you have a Sapphire Radeon RX 9070 NITRO+.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate1 × mounting hardware set1 × thermal pad set1 × 5V ARGB lighting strip2× G1/4 stop plugs

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the system, remove the card, and take off the stock cooler. Clean the old thermal material from the card.
2
Peel the protective film from both sides of each thermal pad. Place the pads on the memory and power stages that meet the block’s raised surfaces. Apply your own thermal paste to the GPU die.
3
Line up the mounting holes on the block, PCB, and backplate. Secure the assembly with the supplied hardware, tightening gradually and evenly.
4
Connect the block to your loop with G1/4 fittings and seal any unused ports. Leak-test the loop with the card unpowered before switching on the system.

You also need a pump, reservoir, radiator, tubing, coolant, and G1/4 fittings that match your tubing.

Bykski A-GV9070GMOC-X installation drawing showing the PCB outline and component positions before applying thermal materials

Bykski installation drawing showing the board before thermal pads and paste are applied.

FAQ

Which water block fits the GIGABYTE RX 9070 XT GAMING OC 16G?

The A-GV9070GMOC-X fits the GV-R9070XTGAMING OC-16GD. Match your card’s PCB layout and mounting holes before ordering.

Does this water block also fit the GIGABYTE RX 9070 GAMING OC 16G?

Yes. The listed RX 9070 GAMING OC card is GV-R9070GAMING OC-16GD.

Is the backplate included?

Yes. The block comes with a passive black anodized aluminum backplate.

What fittings do I need?

Use G1/4 fittings sized for the tubing in your custom loop.

Which lighting header should I use?

Use a compatible 5V 3-pin ARGB header for the RBW strip.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.

FormulaMod Official Store

Recent Reviews
+