• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

PNY RTX 4080 XLR8 VERTO OC Full-Cover GPU Water Block with Backplate | Bykski N-PNY4080VERTO-X

stars, based on ( 0 ) review
€133.25 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-PNY4080VERTO-X

Full-cover water block for the PNY RTX 4080 XLR8 VERTO OC

The Bykski N-PNY4080VERTO-X replaces the stock cooler on the PNY GeForce RTX 4080 16GB XLR8 Gaming VERTO EPIC-X RGB OC with the matching PCB layout. A copper cold plate transfers heat from the GPU, memory, and power delivery components to the coolant circulating through your custom loop.

Fits
PNY RTX 4080 XLR8 VERTO OC
Port thread
G1/4
Lighting
5V 3-pin ARGB
Backplate
Black aluminum

Compatibility

Match the listed card and its PCB layout.

  • ✓PNY GeForce RTX 4080 16GB XLR8 Gaming VERTO EPIC-X RGB OC

PNY identifies this OC card as VCG408016TFXXPB1-O. Before ordering, compare the entire PCB and mounting holes with Bykski’s bare-board photo in the product gallery.

Bykski N-PNY4080VERTO-X fit reference showing the PNY RTX 4080 XLR8 VERTO OC with its original triple-fan cooler

PNY’s photo of the RTX 4080 XLR8 VERTO OC with its factory cooler.

Design Highlights

Bykski N-PNY4080VERTO-X angled view of the clear acrylic water block and black aluminum backplate

A clear top and a separate backplate

The clear acrylic top lets you see the coolant channels and port markings. The included aluminum plate mounts behind the PCB and stays outside the coolant path.

Bykski N-PNY4080VERTO-X design illustration of the jet microchannels in the cold plate

Jet microchannels over the GPU

Coolant passes between closely spaced fins in the cold plate. Bykski specifies a 0.5 mm gap between the fins.

Bykski N-PNY4080VERTO-X clear water block illuminated red, purple, and blue

5V addressable lighting

The ARGB strip lights the acrylic top. Use a matching 5V 3-pin ARGB header and align the connector arrow with +5V.

Key Specifications

ModelN-PNY4080VERTO-X
Cooling coverageGPU core, memory, and voltage regulators
Cold plateCopper
TopClear acrylic
BackplateBlack aluminum
Inlet and outlet threadG1/4
Water block (L × W × T)214.31 × 149.70 × 26.25 mm
Backplate (L × W × T)213.35 × 119.53 × 6.00 mm
Lighting5V 3-pin ARGB (RBW)
Bykski N-PNY4080VERTO-X dimension drawings for the water block and backplate

Water block above, backplate below. Dimensions are in millimeters.

Which Version Do I Need?

Bykski N-PNY4080VERTO-XTHIS PAGE
Choose this clear-top block with 5V ARGB for the matching PNY RTX 4080 XLR8 VERTO OC PCB.
Check this model if you have the PNY RTX 4070 12GB Gaming VERTO PCB.
Choose this version if you want front and rear aluminum armor for the matching PNY RTX 4080 XLR8 VERTO OC PCB.

What's in the Box

1 × full-cover GPU water block with 5V ARGB1 × aluminum backplateThermal pad setMounting hardware set2× G1/4 stop plugsLighting sync cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the PC and remove the graphics card. Take off the stock cooler, clean away the old thermal materials, and check that the mounting holes line up.
2
Cut the supplied thermal pads to fit the areas marked in red. Apply a thin layer of your own thermal paste to the GPU die, shown in blue.
3
Fit the washers and spring screws. Tighten the block evenly in a cross pattern, then secure the backplate with its screws.
4
Connect G1/4 fittings at the marked inlet and outlet. Seal unused openings with stop plugs.
5
Connect the lighting sync cable to a matching 5V 3-pin ARGB header. Align the arrow with +5V.
6
Leak-test the loop before powering the graphics card.

You also need a pump, radiator, G1/4 tube fittings, tubing, and coolant.

Bykski N-PNY4080VERTO-X installation diagram with red thermal pad locations and the GPU die outlined in blue

Red outlines mark the pad locations. The blue outline marks the GPU die.

FAQ

How do I check whether this block fits my PNY RTX 4080?

Check for the XLR8 Gaming VERTO EPIC-X RGB OC model, then compare the complete PCB and mounting holes with the bare-board photo in the product gallery.

What fittings do I need for the water block?

Use G1/4 fittings and choose the tubing connection to match your loop. Follow the inlet and outlet markings on the block.

Can I connect the lighting to a 12V RGB header?

Use a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the lighting.

What else do I need to water-cool the card?

A custom loop needs a pump, radiator, fittings, tubing, and coolant. Leak-test the assembled loop before powering the card.

Notes
  • 36 months against manufacturing defects from the date of purchase. The warranty does not cover compatibility errors or damage from improper installation.
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.

FormulaMod Official Store

Recent Reviews
+