• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Gigabyte RX 6600 XT Eagle GPU Water Block with Backplate | Bykski A-GV6600XT-X

stars, based on ( 0 ) review
$146.41 piece
items available
Contact Us
FormulaMod Official Store
Bykski · A-GV6600XT-X

Full-cover GPU water block for the Gigabyte RX 6600 XT EAGLE

The Bykski A-GV6600XT-X replaces the stock cooler on the Gigabyte Radeon RX 6600 XT EAGLE 8G for use in a custom liquid cooling loop. Its copper cold plate draws heat away from the GPU core, memory, and voltage regulators. The block connects through G1/4 ports and comes with an aluminum backplate.

Fits
Gigabyte RX 6600 XT EAGLE
Port thread
G1/4
Lighting
5V 3-pin ARGB

Compatibility

  • ✓Gigabyte Radeon RX 6600 XT EAGLE 8G (GV-R66XTEAGLE-8GD)

Before ordering, verify the model number and confirm that your card’s PCB layout matches the one specified by Bykski.

Gigabyte Radeon RX 6600 XT EAGLE 8G with its stock fan shroud, shown as a card reference for the Bykski A-GV6600XT-X

Compatible graphics card shown with its stock cooler.

Key Specifications

ModelA-GV6600XT-X
Cold plateT2 high-purity copper
TopClear acrylic
BackplateBlack aluminum (passive)
Port threadG1/4 inlet and outlet
Lighting5V 3-pin ARGB (RBW)
Jet microchannel gap0.5 mm
Block (L × W × T)181.22 × 138.17 × 23.50 mm
Backplate (L × W × T)181.27 × 108.16 × 6.00 mm
Bykski A-GV6600XT-X water block viewed at an angle, showing the clear top, coolant channels, and port openings

What's in the Box

1 × full-cover GPU water block1 × backplateMounting hardware2× G1/4 stop plugs5V ARGB light strip

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Remove the stock cooler and clean the old thermal material from the card.
2
Use the block’s installation diagram to place thermal pads on the indicated memory and power components. Apply your own thermal paste to the GPU die.
3
Align the block with the card’s mounting holes and secure the block and backplate according to the installation diagram.
4
Connect G1/4 fittings to the marked inlet and outlet and seal any unused ports with stop plugs.
5
Leak-test the loop before powering the graphics card.

For the custom loop, you also need a pump, radiator, tubing, G1/4 fittings, and coolant.

FAQ

How do I check whether my RX 6600 XT fits?

Check for Gigabyte model GV-R66XTEAGLE-8GD and verify that its PCB matches Bykski’s compatibility layout.

What fittings does the block take?

Use G1/4 fittings at the marked inlet and outlet.

Which lighting header should I use?

Use a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the light strip.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item. The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.

FormulaMod Official Store

Recent Reviews
+