• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

RTX 4090 AIO Water Cooling Kit for Turbine and Leadtek, 360 mm | Bykski B-FRD-RTX4090

stars, based on ( 0 ) review
998items available
Contact Us
FormulaMod Official Store
Bykski · B-FRD-RTX4090

360 mm liquid cooling for RTX 4090 Turbine and Leadtek boards

The Bykski B-FRD-RTX4090 is a 360 mm all-in-one liquid cooler for GeForce RTX 4090 24 GB Turbine and Leadtek cards with the matching PCB. Its full-cover block replaces the stock cooler and transfers heat from the GPU, memory, and power stages to a radiator mounted in the case.

Fits
RTX 4090 24 GB Turbine / Leadtek
Radiator
360 mm class
Cold plate
T2 copper
Pump
Inline in the tubing

Compatibility

Bykski lists these PCB layouts

  • ✓NVIDIA GeForce RTX 4090 24 GB GDDR6X Turbine
  • ✓Leadtek GeForce RTX 4090 24 GB with Bykski’s listed PCB layout

Compare the mounting holes and component layout on your card with the PCB photo before ordering.

Bykski B-FRD-RTX4090 compatibility photo of the bare GeForce RTX 4090 circuit board with its GPU die and PCIe edge connector

PCB photo from Bykski’s compatibility guide.

Design Highlights

Bykski B-FRD-RTX4090 360 mm kit showing the backplate side of the GPU block, three radiator fans, and the inline pump

Inline pump and case-mounted radiator

The pump sits in the tubing between the GPU block and the aluminum radiator. The three radiator fans on the standard kit move air through the fins to remove heat from the loop.

Bykski B-FRD-RTX4090 cold plate illustration showing the GPU contact area and surrounding machined surfaces

Copper cold plate over three heat sources

The T2 copper cold plate uses 0.3 mm jet microchannels. The block contacts the GPU die and uses thermal pads at the memory and MOSFET power stages.

Key Specifications

ModelBykski B-FRD-RTX4090
Cooler typeFull-cover GPU AIO with backplate
Cold plateT2 copper
Jet microchannels0.3 mm
Block dimensions287.33 × 98.43 × 16 mm
Radiator360 mm class, aluminum
Radiator fans3 shown on the standard 360 mm kit
Pump positionInline in the tubing
Bykski B-FRD-RTX4090 dimension drawing of the block from the side and end

Block dimensions from the manufacturer drawing.

Which Version Do I Need?

Match your card’s PCB first, then check the radiator space in your case.

Bykski B-FRD-RTX4090THIS PAGE
Choose the standard B-FRD-RTX4090-360 for a single matching Turbine or Leadtek card. For a dual-card build, confirm the kit configuration with us before ordering the B-FRD-RTX4090-360-H thick-radiator option.
Choose this separate AIO if your GeForce RTX 4090 matches the AIC Reference PCB shown on its product page.

What's in the Box

Full-cover GPU block and backplate360 mm radiator with inline pump and connected tubingRadiator fans (standard 360 mm kit)

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Shut down and unplug the PC. Remove the graphics card, take off its stock cooler, and clean off the old thermal material.
2
Place thermal pads on the memory and MOSFET locations shown in the diagram. Apply GPU thermal paste to the GPU die.
3
Align the water block and backplate with the card's mounting holes and tighten the screws evenly.
4
Mount the radiator and fans in a 360 mm case position. Check clearances and route the tubing without sharp bends.
5
Connect power to the inline pump and radiator fans. At startup, confirm the pump and fans run and check the tubing connections for leaks.

You also need your own GPU thermal paste, a screwdriver, and a case with clearance for the radiator, fans, and tubing.

Bykski B-FRD-RTX4090 installation drawing showing thermal pad locations and the GPU die

Shaded strips mark the thermal pad locations. The center die takes GPU thermal paste.

FAQ

Can I water-cool my RTX 4090 with this kit?

Yes, if it’s the 24 GB Turbine or Leadtek card and the PCB matches Bykski’s compatibility photo.

Do I need a separate pump for this RTX 4090 AIO?

The pump comes in the assembled cooling circuit with the tubing and radiator. No separate pump or reservoir is needed.

Will the 360 mm radiator fit my case?

Check for a 360 mm radiator mount and enough room for the radiator, fans, and tubing. Bykski shows a top-mounted radiator in its example.

What does -360-H mean on the size selector?

It denotes the 360 mm thick-radiator option listed for dual-card builds. Confirm the kit configuration before ordering for two GPUs.

Notes
  • If the block does not line up with your card, stop and confirm the PCB layout before tightening the screws.

FormulaMod Official Store

Recent Reviews
+