• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

Sapphire NITRO+ RX 9070 XT & RX 9070 Water Block with Backplate | Bykski A-SP9070DD-X

stars, based on ( 0 ) review
$146.41 piece
items available
Contact Us
FormulaMod Official Store
Bykski · A-SP9070DD-X

Full-cover water block for Sapphire NITRO+ RX 9070 series cards

The Bykski A-SP9070DD-X is a full-cover water block for Sapphire NITRO+ Radeon RX 9070 series cards that match the PCB shown below. It replaces the stock cooler and transfers heat from the GPU core, memory, and voltage regulators into your custom liquid cooling loop. The included aluminum backplate mounts behind the board.

Fits
Sapphire NITRO+ RX 9070 / RX 9070 XT
Cold plate
T2 copper
Ports
G1/4 inlet and outlet
Lighting
5V 3-pin ARGB (RBW)

Compatibility

Bykski lists these two Sapphire NITRO+ cards for the PCB layout shown here.

  • ✓Sapphire NITRO+ AMD Radeon RX 9070 XT OC 16GB (11348-01-20G)
  • ✓Sapphire NITRO+ AMD Radeon RX 9070 OC 16GB (11349-01-20G)

Before ordering, check your card’s model number. Compare the component positions and mounting holes on your PCB with Bykski’s drawing.

Bykski A-SP9070DD-X compatibility drawing showing the Sapphire Radeon RX 9070 PCB outline, component positions, and mounting holes

Bykski’s PCB layout drawing for the A-SP9070DD-X.

Design Highlights

Bykski A-SP9070DD-X full-cover GPU water block with a clear top and its port terminal visible

Copper cold plate and clear top

The copper cold plate draws heat from the GPU core, memory, and voltage regulators. The acrylic top leaves the coolant path visible.

Bykski A-SP9070DD-X cold plate showing the central microchannels and the surrounding coolant path

0.3 mm jet microchannels

Coolant passes through a bank of fine channels over the GPU core, where the fins add surface area for heat transfer.

Bykski A-SP9070DD-X water block lit in pink, purple, and blue through the clear acrylic top

5V addressable lighting

Use a compatible 5V 3-pin ARGB connection for the block’s RBW lighting. A 12V 4-pin RGB header is incompatible.

Key Specifications

ModelA-SP9070DD-X
Cooling coverageGPU core, memory, and voltage regulators
Cold plateT2 copper
Jet microchannels0.3 mm
TopClear acrylic
BackplateBlack aluminum, outside the coolant path
Port threadG1/4 inlet and outlet
Water block (L × W × T)219.87 × 146.91 × 26.17 mm
Backplate (L × W × T)219.87 × 116.64 × 5.90 mm
Lighting5V 3-pin ARGB (RBW)

Which Version Do I Need?

Match the full model name on your graphics card label before choosing a block.

Bykski A-SP9070DD-XTHIS PAGE
For the Sapphire NITRO+ RX 9070 or RX 9070 XT shown in Compatibility.
Check this listing if your card is the Sapphire METAL Pulse RX 9070 XT 16GB.
Check this listing for the Gigabyte Radeon RX 9070 XT GAMING OC 16G.

What's in the Box

1 × full-cover GPU water block1 × black aluminum backplate2 × G1/4 stop plugsThermal padsMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Turn off the PC, remove the graphics card, and take off the stock cooler and backplate. Clean away the old thermal material.
2
Place the thermal pads at the memory and power delivery contact points. Apply your own thermal paste to the GPU die.
3
Line up the block and PCB mounting holes. Fit the supplied backplate behind the card and tighten the mounting screws evenly.
4
Use G1/4 fittings to connect the inlet and outlet to your loop. Seal any unused openings with the port plugs.
5
Leak-test the loop with the graphics card unpowered. Power the card only after the loop passes the test.

You’ll also need a pump, a radiator, tubing, coolant, and G1/4 fittings sized for your tubing. For lighting, use a compatible 5V 3-pin ARGB connection.

FAQ

Does this block fit the Sapphire NITRO+ RX 9070 XT?

Bykski lists the Sapphire NITRO+ RX 9070 XT OC 16GB for this block. Before ordering, compare your PCB with the drawing in Compatibility.

Can I use it on a Sapphire PULSE RX 9070 XT?

Bykski’s fit chart for A-SP9070DD-X lists the NITRO+ models shown above. For a PULSE card, look for a water block that explicitly lists your exact card model and PCB.

What fittings do I need?

Use G1/4 fittings that match the tubing in your loop.

Can I plug the lighting into a 12V RGB header?

Use a 5V 3-pin ARGB connection. A 12V 4-pin RGB header is incompatible.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.

FormulaMod Official Store

Recent Reviews
+