• FormulaMod Official Store 0
    Cart Total: items

    Your cart is currently empty..

Bykski

EVGA RTX 3080 / 3080 Ti / 3090 FTW3 Ultra Gaming Water Block with Backplate – Bykski N-EV3090FTW3-X

stars, based on ( 0 ) review
$171.14 piece
items available
Contact Us
FormulaMod Official Store
Bykski · N-EV3090FTW3-X

Full-cover GPU water block for EVGA FTW3 Ultra Gaming

The Bykski N-EV3090FTW3-X replaces the stock cooler on the EVGA GeForce RTX 30-series FTW3 Ultra Gaming boards listed below. In a custom liquid cooling loop, the block moves heat from the GPU, memory, and power delivery components into the coolant. This version includes a passive aluminum backplate and 5V addressable lighting.

Fits
Select EVGA FTW3 Ultra Gaming boards
Ports
G1/4
Backplate
Passive aluminum
Lighting
5V 3-pin ARGB

Compatibility

Confirmed EVGA FTW3 Ultra Gaming PCB layouts

  • ✓EVGA GeForce RTX 3090 FTW3 Ultra Gaming 24GB (24G-P5-3987-KR)
  • ✓EVGA GeForce RTX 3080 Ti FTW3 Ultra Gaming 12GB (12G-P5-3967-KR)

Not compatible:

  • ✗EVGA GeForce RTX 3090 Ti FTW3 Ultra Gaming
  • ✗EVGA GeForce RTX 3080 XC3 Gaming
  • ✗EVGA GeForce RTX 3080 Ti XC3 Gaming

EVGA GeForce RTX 3080 FTW3 Ultra Gaming requires a fit check. Bykski lists this model family. Confirm your exact card part number and PCB layout before ordering.

To confirm fit before ordering, send us your card’s part number and a clear photo of the bare PCB.

Bykski N-EV3090FTW3-X front-side PCB outline with component and mounting-hole positions

Front-side PCB diagram from Bykski’s installation guide.

Design Highlights

Bykski N-EV3090FTW3-X front view showing the clear acrylic top, cold plate, and fitting ports

Cool the GPU, memory, and power delivery

The nickel-plated copper cold plate spans the GPU die, VRAM, and VRM contact areas. The clear acrylic top exposes the coolant path.

Bykski N-EV3090FTW3-X close-up illustration of the GPU cold plate and microchannel fins

Bykski illustration of the cold plate’s microchannel area.

Jet microchannels above the GPU die

Coolant passes through a bank of fine channels above the GPU die. Bykski machines the cold plate from a 9 mm T2 copper plate.

Bykski N-EV3090FTW3-X acrylic water block lit in magenta, blue, and cyan

5V addressable lighting

Use a 5V 3-pin ARGB motherboard header or a compatible 5V controller. A 12V 4-pin RGB header can damage the light strip.

Key Specifications

ModelN-EV3090FTW3-X
Cold plateNickel-plated T2 copper
TopClear PMMA acrylic
Cooling coverageGPU die, VRAM, and VRM
Block length288.79 mm
BackplateBlack aluminum, passive
Backplate dimensions (L × W × T)288.87 × 124.21 × 5 mm
Port threadG1/4 inlet and outlet
Lighting5V 3-pin ARGB (RBW)
Bykski N-EV3090FTW3-X backplate drawing showing length, width, and thickness in millimeters

Bykski backplate drawing. Dimensions are in millimeters.

Which Version Do I Need?

Match the block to your PCB first, then choose the backplate you want.

Bykski N-EV3090FTW3-XTHIS PAGE
Choose this block for a confirmed FTW3 Ultra Gaming PCB and a passive aluminum backplate.
Choose this version if you want coolant routed through the backplate. Check its PCB list before ordering.
Use this listing for the EVGA RTX 3080 XC3 Gaming or RTX 3080 Ti XC3 Gaming.
Use this listing for the EVGA RTX 3090 Ti FTW3 Ultra Gaming.

What's in the Box

1 × full-cover GPU water block1 × passive aluminum backplate5 × 1.5 mm thermal pad strips4 × 0.5 mm insulating washers4 × M2 × 6 mm spring screws6 × M2 × 9.5 mm backplate screws1 × 5V RBW light stripLighting adapter cable2× G1/4 stop plugs

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski N-EV3090FTW3-X included black aluminum backplate with mounting holes

Installation & Use

1
Power down the system. Remove the graphics card, its stock cooler, and its backplate. Clean off the old thermal materials and check that the block’s mounting holes match the PCB.
2
Trim the supplied pads to fit the memory and MOSFET contact areas shown for your PCB. Leave the inductors bare. Apply your own thermal paste to the GPU die.
3
Align the block, PCB, and backplate. Fit the insulating washers around the GPU mounting points, tighten the spring screws gradually in a diagonal pattern, and secure the backplate screws.
4
Connect the block to the loop with G1/4 fittings and seal the unused ports. For motherboard lighting, use the supplied adapter cable on a 5V 3-pin ARGB header and align the arrow with the 5V pin.
5
Fill and bleed the loop. Run only the pump for the leak test and keep the graphics card unpowered until the test is complete.

For a complete loop, you also need a pump, radiator, reservoir, G1/4 fittings matched to your tubing, tubing, and coolant.

Bykski N-EV3090FTW3-X exploded mounting diagram showing the block, GPU board, pads, backplate, and screws

Bykski mounting diagram. 1 water block · 2 thermal pads · 3 your PCB · 4 insulating washers · 5 spring screws · 6 backplate · 7 backplate screws.

FAQ

Does this water block fit my EVGA RTX 3080 FTW3 Ultra Gaming?

Confirm your exact card part number and PCB layout before ordering. Bykski’s compatibility diagram lists the RTX 3080 FTW3 Ultra Gaming model family.

Is the included backplate actively water-cooled?

This version includes a passive aluminum backplate. Coolant runs through the front block.

Which fittings does the block use?

Use G1/4 fittings sized for the tubing in your loop.

Can I connect the lights to a 12V RGB header?

Use a 5V 3-pin ARGB header or compatible 5V controller. A 12V 4-pin RGB header can damage the strip.

Do I need a separate pump and radiator?

Yes. This block is part of a custom loop. Plan for a pump, radiator, reservoir, fittings, tubing, and coolant.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.

FormulaMod Official Store

Recent Reviews
+