Bykski
Bykski GPU Water Cooling Block For XFX RX 6800 / 6800XT V2, With Backplane for Water cooling System, A-XF6800-X
FormulaMod Official Store
click here
Product description:
This full coverage block directly cools the graphics cards core (GPU), graphics memory (RAM), and voltage regulator modules (VRM). By directly cooling these components, you can achieve great temperatures and reach higher overclocks or extend the overall lifespan of your card by running at below-factory temperatures.
The block is constructed of high-purity copper that is nickel electroplated to prevent oxidation. A high-flow design is used to allow multiple blocks to run in series. Top and bottom ports can be used to configure parallel or serial designs in multi-block setups.
The block is constructed of high-purity copper that is nickel electroplated to prevent oxidation. A high-flow design is used to allow multiple blocks to run in series. Top and bottom ports can be used to configure parallel or serial designs in multi-block setups.
Specifications:
Block material: nickel electroplated high purity copper + high quality acrylic
Backplate material: black anodized aluminum (not in contact with coolant)
Backplate material: black anodized aluminum (not in contact with coolant)
Compatibility:
(Including but not limited to the following models)
After narrowing your selection, please check the entire PCB picture to ensure compatibility. If you have any questions, don't hesitate to contact support for confirmation.
Compatibility based on this(these) PCB designs only.
Inlet/outlet port size: G1/4" thread.
XFX Radeon RX 6800 (please compare with PCB)
XFX Radeon RX 6800 XT V2 (please compare with PCB)
After narrowing your selection, please check the entire PCB picture to ensure compatibility. If you have any questions, don't hesitate to contact support for confirmation.
Compatibility based on this(these) PCB designs only.
Inlet/outlet port size: G1/4" thread.
Parts Included:
1x Full coverage GPU water block
1x Backplate
2x Plug fitting
1x Installation screwdriver
1x Lighting sync cable
1x Bykski thermal pads (set)
1x Backplate
2x Plug fitting
1x Installation screwdriver
1x Lighting sync cable
1x Bykski thermal pads (set)
Warnings:
1. Addressable RGB/A-RGB/RBW is 5V 3pin lighting system, and is ONLY compatible with 5V components.
RGB is 12V 4pin lighting system, and is ONLY compatible with 12V components.
Mix and match will NOT work and will cause damage.
2. This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
3. The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal pad. In the middle part of product gallery images, there will be a picture description/display where the thermal pad should be placed. Installing pads on other components can lead to improper contact and poor performance.
4. Not responsible for any damage caused by or when using this product. Please use it at your own risk.
RGB is 12V 4pin lighting system, and is ONLY compatible with 12V components.
Mix and match will NOT work and will cause damage.
2. This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
3. The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal pad. In the middle part of product gallery images, there will be a picture description/display where the thermal pad should be placed. Installing pads on other components can lead to improper contact and poor performance.
4. Not responsible for any damage caused by or when using this product. Please use it at your own risk.
By
Anthony
Thursday, 20 January 2022Originally installed this cooler using the existing size and thickness thermal pads described in the XFX documentation as the instructions here aren't really that clear . Cooler did not work and the card overheated.IT WAS MY FAULT.... There are only a few thermal pads required in the install:Nothing on the back of the card.Existing thermal pads on the metal frame are not needed. (red crosses)Because i only had 1.5mm thermal pads. (require 1.8mm NOT 2mm) i applied thermal paste to the chips (marked green) to fill out the extra space.This has me stable at 31c idle and max out at 85c in full res VR. Customer service was very quick and helpful... Happy to be using their product.
By
Peter
Thursday, 18 November 2021Was skeptical about ordering, After much research it appears all my local PC shops have order the other variant of this water block for non overseas models. Good communication by staff they really helped me out and answered my stupid questions. DHL express shipping it arrived in AU within 5 Days.The block itself is very good the quality is better than many other blocks much more expensive temp consistently in the 40c while under hard load with a 240/360mm loop 10/10 will be a regular customer and can also recommend BYSKI to anyone interesedCheers.
